Isuzu NHR 4J Series Workshop Manual Download Page 331 | Manualshive

Page: 331 / 406

background image

6D1 – 6 ENGINE ELECTRICAL

JUMP STARTING PROCEDURE

1. Set the vehicle parking brake.

If the vehicle is equipped with an automatic
transmission, place the selector lever in the "PARK"
position.

If the vehicle is equipped with a manual transmission
place the shift lever in the "NEUTRAL" position.

Turn "OFF" the ignition.

Turn "OFF" all lights and any other accessory requiring
electrical power.

2. Look at the built-in hydrometer.

If the indication area of the built-in hydrometer is
completely clear, do not try to jump start.

3. Attach the other end of the same cable to the positive

terminal of the discharged battery.

Attach the end of one jumper cable to the positive
terminal of the booster battery.

Do not allow the vehicles to touch each other.

This will cause a ground connection, effectively
neutralizing the charging procedure.

Be sure that the booster battery has a 12 volt rating.

4. Attach one end of the remaining cable to the negative

terminal of the booster battery.

Attach the other end of the same cable to a solid
engine ground (such as the A/C compressor bracket
or the generator mounting bracket) of the vehicle with
the discharged battery.

This ground connection must be at least 450 mm (18
in) from the battery of the vehicle whose battery is
being charged.

«
...
329
330
331
332
333
...
»

Summary of Contents for NHR 4J Series























































































































































































































































































































































































































Reviews:

No comments

Related manuals for NHR 4J Series

Brand: Farymann Diesel Pages: 80

Brand: brel-motors Pages: 2

Brand: KONTRONIK Pages: 11

Brand: Volkswagen Pages: 64

Brand: SPE Pages: 7

Brand: TEM Pages: 19

75-200 V DC Series

Brand: TEM Pages: 38

Brand: TEM Pages: 42

Brand: Volvo Pages: 8

Brand: Volvo Pages: 88

Brand: JaxSon Pages: 40

Brand: Briggs & Stratton Pages: 11

Brand: Indian Motorcycle Pages: 50

Brand: Ober Pages: 32

Brand: SKY Engines Pages: 39

Brand: Mitsubishi Pages: 42

Brand: IAME Pages: 45

Brand: InMotor Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands