Isuzu NHR 4J Series Workshop Manual Download Page 49

Page: 49 / 406

SERVICE INFORMATION 00 – 45

ENGINE CONTROL

Idling Speed Inspection

1. Set the vehicle parking brake and choke the drive

wheels.

2. Place the transmission in neutral.
3. Start the engine and allow it to warm up.
4. Disconnect the engine control cable from the control

lever.

5. Set a tachometer to the engine.
6. Check the engine idling speed.

If the engine idling speed is outside the specified
range, it must be adjusted.

Engine Idling Speed

rpm

4JB1 / 4JB1T / 4JB1TC

750 - 790

4JG2

700 - 740

Idling Speed Adjustment

1. Loosen the idling set bolt lock nut on the injection

pump idling set bolt.

2. Adjust the idling speed to the specified range by

turning the idling set bolt.

3. Lock the idling set bolt with the idling set bolt lock nut.
4. Check that the idling control cable is tight (free of

slack).
If required, remove the slack from the cable.

Accelerator Control Cable Adjustment

1. Loosen the accelerator cable clamp bolt.
2. Check that the idling control knob on the instrument

panel is in the engine idling position.

3. Hold the accelerator lever in the fully closed position

and stretch the control cable in the direction indicated
by the arrow to remove any slack.

Accelerator Pedal Adjustment

1. Loosen the lock nut.
2. Adjust bolt height from floor.
Adjust Bolt Height A

mm (in)

18 - 28 (0.71 - 1.1)

0044-1.tif

0044-2.tif

Summary of Contents for NHR 4J Series























































































































































































































































































































































































































Search results

Summary of Contents for NHR 4J Series

Reviews:

Related manuals for NHR 4J Series

Brands by name

Popular brands

Isuzu NHR 4J Series, Workshop Manual

Search results

Summary of Contents for NHR 4J Series

Reviews:

Related manuals for NHR 4J Series

Brands by name

Popular brands