Isuzu NHR 4J Series Workshop Manual Download Page 282 | Manualshive

Page: 282 / 406

background image

ENGINE FUEL 6C - 23

DISASSEMBLY (4JBI/4JB1T Engine)

1. Retaining Nut

2. Injection Nozzle

1) Remove the nozzle assemblies from the nozzle

holders.
Tag the nozzle assemblies and the nozzle holders to
ensure that they are reinstalled in their original
positions.
The nozzle assembly and nozzle holder combinations
must not be interchanged.

2) Immerse the injection nozzle in a tool tray filled with

clean diesel oil to protect them from dust.

3. Spacer

4. Spring Seat

5. Spring

6. Adjusting Shim

7. Nozzle Holder

INSPECTION AND REPAIR (4JB1/4JB1 T
Engine)

Make the necessary adjustments, repairs, and part
replacements if excessive wear or damage is discovered
during inspection.

Inspection Nozzle Needle Inspection

1. Remove the needle from the nozzle body.
2. Carefully wash the nozzle needle and the nozzle body

in clean diesel fuel.

3. Check that the nozzle needle moves smoothly inside

the injection nozzle body.
If the nozzle needle does not move smoothly, it must
be repaired (See "Nozzle Lapping Procedure" belows).

6C-22-1.tif

6C-22-2.tif

6C-22-3.tif

«
...
280
281
282
283
284
...
»

Summary of Contents for NHR 4J Series























































































































































































































































































































































































































Reviews:

No comments

Related manuals for NHR 4J Series

Brand: Zundapp Pages: 52

Brand: Guangxi Liuzhou Wuling Motors Pages: 54

Brand: Hitachi Pages: 41

Brand: Hitachi Pages: 1037

Brand: Hitachi Pages: 1104

Powertrain 4.3 L

Brand: GMC Pages: 196

Brand: Texas Equipment Pages: 38

Brand: Panther Pages: 7

Brand: Tahmazo Pages: 3

Brand: KRESS Pages: 46

Brand: Motion Pages: 92

Brand: Hotsy Pages: 68

Brand: Mitsubishi Heavy Industries Pages: 65

Brand: Mitsubishi Heavy Industries Pages: 78

Brand: Mitsubishi Heavy Industries Pages: 220

Brand: CRRC-pro Pages: 8

Brand: SEW-Eurodrive Pages: 4

Brand: Mitsubishi Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands