Isuzu NHR 4J Series Workshop Manual Download Page 278

Page: 278 / 406

ENGINE FUEL 6C - 19

5. Secure the dial gauge to the nozzle holder using the

nut so that the pin contacts the tip of the first spring
seat.

CAUTION:

•

Secure the dial gauge so that a stroke of 2 mm can
be measured.

•

Do not over-tighten the nut as the dial gauge shaft
may jam. (Confirm from the dial gauge that the
shaft moves smoothly.)

6. Set the nozzle holder to the nozzle tester and put

needle to zero on the dial gauge.

7. Operate the nozzle tester to bleed any air from inside

the retaining nut and to confirm that no fuel leaks.

8. Operate the nozzle tester and increase the in-line

pressure to 34.3 - 44.1 MPa (350 - 450 kg/cm

) so that

the nozzle’s needle valve moves through its full lift.
Record full lift ‘L’. (Read dial gauge)

Note:

The above operation is used to determine whether
the nozzle seat is worn and whether the nozzle
assembly is in good condition.

040MV009.tif

040MV030.tif

040MV008.tif

Summary of Contents for NHR 4J Series























































































































































































































































































































































































































Search results

Summary of Contents for NHR 4J Series

Reviews:

Related manuals for NHR 4J Series

Brands by name

Popular brands

Isuzu NHR 4J Series, Workshop Manual

Search results

Summary of Contents for NHR 4J Series

Reviews:

Related manuals for NHR 4J Series

Brands by name

Popular brands