Isuzu NHR 4J Series Workshop Manual Download Page 281 | Manualshive

Page: 281 / 406

background image

6C - 22 ENGINE FUEL

Second nozzle opening pressure adjustment

If the second nozzle opening pressure is not as specified,
disassemble the nozzle from the nozzle holder and
replace the shim until the pressure is as specified.

CAUTION:

•

Because the second opening pressure changes
when the first opening pressure changes, the
second opening pressure must be adjusted when
the first opening pressure changes.

•

Use a micrometer to measure shim thickness.

•

Second nozzle opening pressure adjusting shims

Part No.

Thickness (mm)

8-9711-6034-0

0.40

8-9711-6035-0

0.50

8-9711-6037-0

0.52

8-9711-6039-0

0.54

8-9711-6041-0

0.56

8-9711-6043-0

0.58

8-9711-6044-0

0.59

Final inspection

1. Remove the dial gauge, nut and dial gauge holder.

2. Remove the adjustment retaining nut and gasket.
3. Install the original retaining nut, confirm that the pins

are inserted fully into the nozzle, and then hand-tighten
the retaining nut. Then, tighten the original retaining
nut to the specified torque.
Torque: 59 - 79 N

∙

m (6.0 - 8.0 kg

∙

m)

4. Set the nozzle holder to the nozzle tester and check

first nozzle opening pressure, spray condition, seat oil
tightness and each part for oil leaks.

5. When replacing the nozzle, replace the nozzle, lift

piece, pins and spacer as a set with the nozzle service
kit.

CAUTION:

Pre-lift will not be as specified if only the nozzle is
replaced.

040MV017.tif

040LX009.tif

040MV028.tif

040MV014-1.tif

040MV030.tif

«
...
279
280
281
282
283
...
»

Summary of Contents for NHR 4J Series























































































































































































































































































































































































































Reviews:

No comments

Related manuals for NHR 4J Series

IE3-K11R 132S 4 Ex e IIC T3

Brand: VEM Pages: 16

Brand: Doosan Pages: 350

Brand: Engine distributors Pages: 331

Brand: GAPOSA Pages: 2

Brand: Guangxi Liuzhou Wuling Motors Pages: 54

Brand: Sachs Pages: 42

50-400 V CA Series

Brand: TEM Pages: 44

Brand: Yanmar Pages: 35

CLEARPATH CPM-MCVC-3421S-RLN

Brand: Teknic Pages: 203

Brand: TAARKS Pages: 9

Brand: Beamz Pages: 6

Brand: JAC Pages: 14

Brand: Mitsubishi Pages: 216

Brand: Mitsubishi Pages: 16

Brand: Nanni Pages: 129

Brand: Jamara Pages: 2

Brand: Nanni Pages: 93

Brand: WÄRTSILÄ Pages: 178

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands