Isuzu NHR 4J Series Workshop Manual Download Page 173

Page: 173 / 406

6A1 – 38 4JB1/4JB1T/4JB1TC/4JG2 - ENGINE

2. Heater Hose

•

Disconnect heater hose from heater pipe.

3. A/C Compressor Drive Belt

•

Loosen idler lock nut.

•

Loosen adjust bolt and remove drive belt.

4. Engine Harness

•

Disconnect harness connectors from units on
thermostat housing.

5. Air Intake Duct

•

Remove the clip and air intake duct.

6. Injection Pipe

•

Release injection pipe clip.

•

Remove flare nut injection pump side.

•

Remove flare nut injection nozzle side and remove
injection pipe.

NOTE:

Plug the injection nozzle holder and the delivery
holder to prevent the entry of foreign matters into
them.

7. Leak Off Pipe

•

Remove the leak off pipe side of leak off hose.

8. PCV Hose

•

Remove the PCV hose from air intake pipe.

6A1-38-1.tif

6A1-38-2.tif

Summary of Contents for NHR 4J Series























































































































































































































































































































































































































Search results

Summary of Contents for NHR 4J Series

Reviews:

Related manuals for NHR 4J Series

Brands by name

Popular brands

Isuzu NHR 4J Series, Workshop Manual

Search results

Summary of Contents for NHR 4J Series

Reviews:

Related manuals for NHR 4J Series

Brands by name

Popular brands