Isuzu NHR 4J Series Workshop Manual Download Page 279

Page: 279 / 406

6C - 20 ENGINE FUEL

Pre-lift confirmation

1. With the needle valve at full lift, release the nozzle

tester handle.

Note:

The in-line pressure will decrease and needle
valve lift (as indicated on the dial gauge) will also
decrease a little.

2. Read the needle valve lift ‘liter’ from the dial gauge

indication (once the needle valve has descended when
the second spring has stopped operating). Refer to the
pre-lift measuring point for ‘liter’.

Pre-lift measuring point:

Read the dial gauge at first nozzle opening prapprox 1
MPa (10 kg/cm

Note:
This point can be found while the pressure is
decreasing.

3. Confirm that pre-lift ‘liter’ is as specified.
Pre-lift

0.04

4. If pre-lift is not as specified, replace the pins, lift piece,

spacer and nozzle assembly as a set with the service
kit.

Service kit:

8-9720-3470-1

040MV007.tif

040MV006.tif

040MV025-1.tif

040MV005.tif

040MV031.tif

Summary of Contents for NHR 4J Series























































































































































































































































































































































































































Search results

Summary of Contents for NHR 4J Series

Reviews:

Related manuals for NHR 4J Series

Brands by name

Popular brands

Isuzu NHR 4J Series, Workshop Manual

Search results

Summary of Contents for NHR 4J Series

Reviews:

Related manuals for NHR 4J Series

Brands by name

Popular brands