Isuzu NHR 4J Series Workshop Manual Download Page 115 | Manualshive

Page: 115 / 406

background image

6A – 48

GENERAL ENGINE MECHANICAL

7. Piston Ring

Remove the piston rings with a piston ring expander.
Arrange the removed piston rings in the cylinder number
order.

8. Piston Pin Snap Ring

•

Use a pair of pliers to remove the piston pin snap
rings.

9. Piston Pin

NOTE:

Keep the parts removed from each cylinder separate.
All parts must be reinstalled in their original positions.

10. Piston

11. Connecting Rod

INSPECTION AND REPAIR

PISTON AND PISTON RING

Pistons

Carefully clean away all the carbon adhering to the piston
head and the piston ring grooves.

NOTE:

Never use a wire brush to clean the pistons. Damage will
result.
Visually check each piston for cracking, scoring, and other
signs of excessive wear.
If any of the above conditions are present, the piston must
be replaced.

Piston Diameter

1. Measure the piston outside diameter with micrometer

at the piston grading position.

Piston Grading Position

mm (in)

4JB1 / 4JB1T / 4JB1TC

74 (2.913)

4JG2

71.00 (2.797)

6A-48-2.tif

6A-48-3.tif

6A-48-1.tif

«
...
113
114
115
116
117
...
»

Summary of Contents for NHR 4J Series























































































































































































































































































































































































































Reviews:

No comments

Related manuals for NHR 4J Series

SEL Plus-RC Series

Brand: Selve Pages: 172

Brand: Kuda Pages: 98

Brand: Habasit Pages: 54

Brand: Saito Pages: 2

Brand: CESARONI Pages: 6

Brand: Oriental motor Pages: 8

Brand: Oriental motor Pages: 12

Brand: Volvo Penta Pages: 41

EASY-KART 100cc

Brand: IAME Pages: 35

Brand: Volvo Penta Pages: 136

Brand: Lister Petter Pages: 88

Brand: Bauer Pages: 52

Brand: Stober Pages: 34

Brand: O.S. engine Pages: 11

Brand: Honda Pages: 130

Brand: Stiga Pages: 65

Brand: Honda Pages: 162

Brand: Ibi Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands