Isuzu NHR 4J Series Workshop Manual Download Page 355 | Manualshive

Page: 355 / 406

background image

6D3 – 10 CHARGING SYSTEM

6. Rotor

•

With the rotor gripped with a vise, remove the pulley
nut

!

, and then take off the pulley

"

, fan

#

, front

cover

$

and the rotor

%

.

7. Rear Bearing

8. Terminal Bolt and Nut

9. Rear

Cover

•

Remove the nuts fixing the B terminal and diode
holder.
Separate the stator and rear cover.
Note the position of insulation washers to ensure
reassembly into original position.

10. Stator

11. Diode

•

Separate the diodes from the stator by melting away
solder on stator coil and diode.
When melting solder, hold the lead wire with long nose
pliers to prevent heat from being transferred to the
diodes.

12. IC Regulator Assembly

•

Separate the IC regulator from the diode by melting
away solder on IC regulator holder plate and removing
the nut.

13. Brush Holder

•

Remove the serrated bolts and melt away solder on IC
regulator.

•

Do not remove the serrated bolts unless the
replacement of brush or condenser.
To install, follow the removal steps in the reverse
order.

INSPECTION AND REPAIR

Repair or replace necessary parts if extreme wear or
damage is found during inspection.

6D3-10-1.tif

6D3-10-3.tif

6D3-10-4.tif

6D3-10-2.tif

«
...
353
354
355
356
357
...
»

Summary of Contents for NHR 4J Series























































































































































































































































































































































































































Reviews:

No comments

Related manuals for NHR 4J Series

Brand: Fagor Pages: 174

Brand: Saab Pages: 30

MICROPUMP EagleDrive MS

Brand: Idex Pages: 23

Brand: Kohler Pages: 4

Brand: Yamaha Pages: 30

Brand: Forest-Master Pages: 16

Brand: Lycomin Pages: 171

Brand: Yanmar Pages: 317

Brand: O.S. engine Pages: 2

Brand: O.S. engine Pages: 4

Brand: O.S. engine Pages: 2

Brand: O.S. engine Pages: 4

Brand: O.S. engine Pages: 22

Max-50SX-H Ring

Brand: O.S. engine Pages: 28

Brand: O.S. engine Pages: 21

Brand: WilTec Pages: 16

Brand: WilTec Pages: 26

Brand: Motion Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands