Isuzu NHR 4J Series Workshop Manual Download Page 225 | Manualshive

Page: 225 / 406

background image

6A1 – 90 4JB1/4JB1T/4JB1TC/4JG2 - ENGINE

INSTALLATION

14. Crankshaft and Main Bearings

•

The crankshaft upper bearings have an oil hole and an
oil groove. The lower bearings do not…

•

Install main bearings in the cylinder body and main
bearing cap respectively.

•

Apply new engine oil to upper and lower main
bearings.

•

Make sure that main bearing are in correct position.

•

Carefully wipe any foreign material from the upper
bearing.

•

Install the main bearings to the cylinder body and the
main bearing caps.

NOTE:

Do not apply engine oil to the bearing back faces and
the cylinder body bearing fitting surfaces.

•

Be sure that they are positioned correctly.

•

Apply new engine oil to the upper and lower main
bearing faces.

•

Carefully mount the crankshaft.

•

Apply engine oil to the thrust washer.

•

Install thrust washer on No.3 journal.
Oil grooves in thrust washer must face the crankshaft.

•

Apply the recommended liquid gasket or its equivalent
to the No.5 crankshaft bearing cap cylinder body fitting
surfaces at points and shown in the illustration.

NOTE:

Be sure that the bearing cap fitting surface is
completely free of oil before applying the liquid
gasket.

Do not allow the liquid gasket to obstruct the cylinder
thread holes and bearings.

6A1-90-1.tif

6A1-90-2.tif

6A1-90-3.tif

6A1-90-4.tif

«
...
223
224
225
226
227
...
»

Summary of Contents for NHR 4J Series























































































































































































































































































































































































































Reviews:

No comments

Related manuals for NHR 4J Series

Brand: M+S Pages: 6

Brand: FeiaoModel Pages: 7

Vanguard 540000 Series

Brand: Briggs & Stratton Pages: 32

Brand: ALL POWER AMERICA Pages: 28

Brand: IEF Werner Pages: 38

Brand: Waterworld Pages: 30

Calzoni MR Series

Brand: Parker Pages: 50

Brand: YS Pages: 2

Brand: Detroit Diesel Pages: 22

Brand: Novy Pages: 18

HSK35,40, HSSK50

Brand: Tecumseh Pages: 8

Brand: Wood-mizer Pages: 146

Brand: Marine Power Pages: 45

Brand: Grundfos Pages: 12

Brand: Vetus Pages: 84

Brand: HRW Pages: 23

Brand: California Air Tools Pages: 16

Brand: UMS Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands