Isuzu NHR 4J Series Workshop Manual Download Page 192 | Manualshive

Page: 192 / 406

background image

4JB1/4JB1T/4JB1TC/4JG2 – ENGINE 6A1 – 57

6) Tap the piston pin out with a hammer and a brass bar.

If the pistons and piston pins are to be reinstalled,
mark their installation positions by tagging each piston
and piston pin with the cylinder number from which it
was removed.

INSTALLATION

6. Piston and Connecting Rod Assembly

1) Try to insert the piston pin into the piston pin hole with

normal finger pressure.
Weigh each piston and connecting rod assembly.
Select piston and connecting rod combinations so that
the weight variation of the different assemblies is held
within the specified limits.

g(oz)

Variance in weight

Less than

after assembly

3(0.1058)

2) Clamp the connecting rod in a vise.

Take care not to damage the connecting rod.

3) Use a pair of pliers to install the piston pin snap ring to

the piston.

NOTE:

When changing piston/connecting rod combinations,
do not change the piston/piston pin combination.

4) Install the piston to the connecting rod.

The piston head front mark

!

and the connecting rod

"ISUZU" casting mark

"

must be facing the same

direction.

6A1-57-1.tif

6A1-57-2.tif

6A1-57-3.tif

«
...
190
191
192
193
194
...
»

Summary of Contents for NHR 4J Series























































































































































































































































































































































































































Reviews:

No comments

Related manuals for NHR 4J Series

Brand: Daihatsu Pages: 196

Brand: nord Pages: 12

Brand: Flux Pages: 20

Brand: Onan Pages: 341

2-10-4 TEXAS STEAM ENGINE

Brand: Premier Pages: 24

Brand: ACDC Pages: 20

Brand: Protek Pages: 20

Brand: Volvo Penta Pages: 96

Brand: Volvo Penta Pages: 106

Brand: Maverick Pages: 12

Brand: GPOWER Pages: 4

Brand: Winterthur Gas Pages: 495

Brand: Daewoo Pages: 165

Brand: TOHATSU Pages: 87

Brand: Fanotec Pages: 2

Brand: DANA Pages: 3

Brand: Ingersoll-Rand Pages: 4

Brand: Mitsubishi Heavy Industries Pages: 65

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands