manualshive.com logo in svg

Isuzu NHR 4J Series, Workshop Manual

The Isuzu NHR 4J Series Workshop Manual is the ultimate guide for maintaining and repairing your vehicle. Easily download the manual for free from manualshive.com, providing you with all the necessary information to keep your Isuzu NHR 4J Series in top condition. Get your copy now and drive with confidence.

Share
Download
background image

6A1 – 72  4JB1/4JB1T/4JB1TC/4JG2 - ENGINE

6. Front Oil Seal

•

Use a plastic hammer and a screwdriver to top around
the oil seal to free it from the gear case cover.
Take care not to damage the oil seal fitting surfaces.

INSTALLATION

6. Front Oil Seal

•

Use the installer to install the front oil seal 

!

 to the

gear case cover 

"

.

Oil Seal Installer: 5-8840-2061-0
Note the oil seal installation depth 

#

 shown in the

illustration.
Depth 

#

 = 1 mm (0.039 in.)

5. Crankshaft Damper Pulley

Tighten the crankshaft damper pulley bolt to the specified
torque.

NOTE:

Hold the flywheel ring gear stationary to prevent the
crankshaft from turning when tightening the damper
pulley.

Pulley Boss Bolt Torque

N

∙

m (kg

∙

m/lb

∙

ft)

                                                                                                                   

206 (21/152)

                                                                                                                   

4. Cooling Fan Assembly

•

Mount fan pulley, distance piece, and cooling fan asm
(in this order) on the water pump, and tighten to the
specified torque.

N

∙

m (kg

∙

m/lb

∙

in)

                                                                                                                   

8 (0.8/69)

                                                                                                                   

3. AC Generator Drive Belt

•

Install AC Generator drive belt and adjust belt tension.

•

Refer to Drive Belt Adjustment in this section.

2. Power Steering Pump Drive Belt

•

Install power steering pump drive belt and adjust belt
tension.

•

Refer to “Drive Belt Adjustment” in this section.

1. Fan Shroud

•

Install the fan shroud and reservoir tank hose.

•

Pour coolant

•

Start the engine and check coolant leakage.

6A1-72-3.tif

6A1-72-2.tif

6A1-72-1.tif

Summary of Contents for NHR 4J Series























































































































































































































































































































































































































Reviews:

No comments

Related manuals for NHR 4J Series

Fagor FXM1 Series Installation Manual preview
FXM1 Series
Brand: Fagor Pages: 174
WPT POWER PILOTLESS Installation & Maintenance Manual preview
PILOTLESS
Brand: WPT POWER Pages: 39
nord BU 0135 Starter Manual preview
BU 0135
Brand: nord Pages: 91
Selve SE-R Series Adjustment Instructions Manual preview
SE-R Series
Brand: Selve Pages: 24
ABB M3LK 250 Additional Manual preview
M3LK 250
Brand: ABB Pages: 13
Lister Petter T Series Operator'S Handbook Manual preview
T Series
Brand: Lister Petter Pages: 81
Lister Petter TS/TR1 Workshop Manual preview
TS/TR1
Brand: Lister Petter Pages: 100
Volvo Penta TAD570VE Operator'S Manual preview
TAD570VE
Brand: Volvo Penta Pages: 96
Volvo Penta TAD1340VE Operator'S Manual preview
TAD1340VE
Brand: Volvo Penta Pages: 106
Louvolite R1710 Programming Instructions preview
R1710
Brand: Louvolite Pages: 4
Modelix Ultimate MX8 Racing Instruction Manual preview
Ultimate MX8 Racing
Brand: Modelix Pages: 7
NSK NLX Plus Operation Manual preview
NLX Plus
Brand: NSK Pages: 62
NSK VOLVERE i7 Operation Manual preview
VOLVERE i7
Brand: NSK Pages: 110
DLE 85 User Manual preview
85
Brand: DLE Pages: 4
DLE 222 User Manual preview
222
Brand: DLE Pages: 4
DANA 4360-57 Parts List preview
4360-57
Brand: DANA Pages: 3
DANA 4360-50 Parts List preview
4360-50
Brand: DANA Pages: 3
TTBIO Vigor A65 Operation Manual preview
Vigor A65
Brand: TTBIO Pages: 2

Brands by name

Popular brands

Load more brands