Isuzu NHR 4J Series Workshop Manual Download Page 181

Page: 181 / 406

6A1 – 46 4JB1/4JB1T/4JB1TC/4JG2 - ENGINE

5. Air Intake Duct

4. Engine Harness

•

Connect the thermo-sensor harness and thermo-meter
unit harness.

3. A/C Compressor Drive Belt (A/C Model)

Check drive belts for wear or damage, and replace with
new ones as necessary. Check belts for tension, and
adjust as necessary.
•

Check drive belts tension.

•

Push the middle of belts with a force of 10kg and
check each bolt for deflection.

•

Standard deflection

mm (in)

Initial tension

AC generator & fan pulley drive belt

A/C compressor drive belt

P/S pump drive belt

8 - 12 (0.31 - 0.47)

TENSION ADJUSTMENT

P/S oil pump and A/C compressor pulley belt
•

With P/S pump lock bolt loose, adjust belt tension with
adjust belt.

Cooling fan pulley belt
•

With AC Generator mounting and lock bolts loose,
adjust belt tension with adjuster's adjust bolt.

Torque Standard

∙

m (kg

∙

m/lb

∙

ft)

AC generator fixing bolt

40 (4.1/30)

Adjust plate fixing bolt

19 (1.9/14)

Adjust plate lock bolt

19 (1.9/14)

6A1-46-1.tif

6A1-46-2.tif

6A1-46-3.tif

6A1-46-4.tif

Summary of Contents for NHR 4J Series























































































































































































































































































































































































































Search results

Summary of Contents for NHR 4J Series

Reviews:

Related manuals for NHR 4J Series

Brands by name

Popular brands

Isuzu NHR 4J Series, Workshop Manual

Search results

Summary of Contents for NHR 4J Series

Reviews:

Related manuals for NHR 4J Series

Brands by name

Popular brands