Isuzu NHR 4J Series Workshop Manual Download Page 214

Page: 214 / 406

4JB1/4JB1T/4JB1TC/4JG2 – ENGINE 6A1 – 79

2) Clutch
•

Raise vehicle and support with suitable safety stands.

CAUTION:

Do not let clutch fluid remain on a painted surface,
Wash it off immediately.

Pressure Plate Assembly

Driven Plate Assembly

•

Use the pilot aligner to prevent the driven plate
assembly from falling free.
Pilot Aligner: 5-5825-3001-0

•

Mark the flywheel and pressure plate lug for alignment
when installing.

•

Loosen the pressure plate assembly fixing bolts.

2. Flywheel

3. Rear Oil Seal

•

With the oil seal pushed in deep, install the special tool
as shown in the illustration to remove the oil seal.

•

Rear oil seal Remove: 5-8840-2360-0

NOTE:

Take care not to damage the crankshaft or oil seal
retainer when removing oil seal.

6A1-79-1.tif

6A1-79-2.tif

Summary of Contents for NHR 4J Series























































































































































































































































































































































































































Search results

Summary of Contents for NHR 4J Series

Reviews:

Related manuals for NHR 4J Series

Brands by name

Popular brands

Isuzu NHR 4J Series, Workshop Manual

Search results

Summary of Contents for NHR 4J Series

Reviews:

Related manuals for NHR 4J Series

Brands by name

Popular brands