Isuzu NHR 4J Series Workshop Manual Download Page 242

Page: 242 / 406

4JB1/4JB1T/4JB1TC/4JG2 – ENGINE 6A1 – 107

1) Transmission

)

Mounting Bracket

Mounting Bracket Nuts Torque

∙

m (kg

∙

m/lb

∙

ft)

69 (7.0/51)

(

Transmission Assembly

•

Support the transmission with mission jack.

CAUTION:

To prevent the falling of the transmission, tie it
securely to the jack with a chain or belt.

•

Shift transmission into high gear.

•

Align transmission with engine slope.

•

Turn output parking brake drum to aid clutch spring
engagement.

Clutch Housing to Flywheel
Housing Bolts Torque

∙

m (kg

∙

m/lb

∙

ft)

M10 : 46(4.7/34)
M12 : 91(9.3/67)

•

Raise engine and transmission up into rear
transmission mount.

Engine Rear Mounting Nuts
and Bolts Torque

∙

m (kg

∙

m/lb

∙

ft)

M10 : 40(4.1/30)
M12 : 69(7.0/51)

6A1-107-1.tif

6A1-107-2.tif

Summary of Contents for NHR 4J Series























































































































































































































































































































































































































Search results

Summary of Contents for NHR 4J Series

Reviews:

Related manuals for NHR 4J Series

Brands by name

Popular brands

Isuzu NHR 4J Series, Workshop Manual

Search results

Summary of Contents for NHR 4J Series

Reviews:

Related manuals for NHR 4J Series

Brands by name

Popular brands