Isuzu NHR 4J Series Workshop Manual Download Page 164

Page: 164 / 406

4JB1/4JB1T/4JB1TC/4JG2 – ENGINE 6A1 – 29

3. AC Generator Drive Belt

•

Install AC Generator drive belt and adjust belt tension.

•

Depress the drive belt mid-portion with a 98N
(10kg/22lb) force.

Drive Belt Deflection

mm (in)

8 (0.31) - 12 (0.47)

•

Tighten the idler lock nut to the specified torque.

∙

m (kg

∙

m/lb

∙

ft)

27 (2.8/20)

2. Power Steering Pump Drive Belt (P/S Model)

•

Install Power Steering pump drive belt and adjust belt
tension.

•

Depress the drive belt mid-portion with a 98N
(10kg/22lb) force.

Drive Belt Deflection

mm (in)

8 (0.31)-12(0.47)

•

Tighten the idler lock nut to the specified torque.

∙

m (kg

∙

m/lb

∙

ft)

27 (2.8/20)

1. Fan shroud

•

Install the fan shroud and reservoir tank hose.

•

Pour coolant

•

Start the engine and check coolant leakage.

Summary of Contents for NHR 4J Series























































































































































































































































































































































































































Search results

Summary of Contents for NHR 4J Series

Reviews:

Related manuals for NHR 4J Series

Brands by name

Popular brands

Isuzu NHR 4J Series, Workshop Manual

Search results

Summary of Contents for NHR 4J Series

Reviews:

Related manuals for NHR 4J Series

Brands by name

Popular brands