Isuzu NHR 4J Series Workshop Manual Download Page 121 | Manualshive

Page: 121 / 406

background image

6A – 54

GENERAL ENGINE MECHANICAL

•

Attach the piston to the connecting rod with the piston
front mark and the connecting rod ISUZU mark on the
same side.

7. Piston Ring

•

Install the piston rings with the piston ring expander.
The compression ring must be set with the 1N, 2N
mark (4JG2) facing up.

•

Discrimination mark is painted as shown in the
illustration.

•

Install piston rings in the following sequence.

1) Oil ring

!

Expander ring

"

Upper side rail

#

Lower side rail

2) 2nd compression ring

3) 1st compression ring

•

The compression ring must be set with the 1N or 2N
mark (4JG2) facing up.

•

1st compression ring: 1N (4JG2), N (4JB1)

•

2nd compression ring: 2N (4JG2), N (4JB1)

•

After installation, apply engine oil to the entire
circumference of the piston rings.
Check to see that all the rings rotate smoothly.

•

Insert the bearings into the connecting rods and caps.
Apply new engine oil to the bearing faces.
Cap side bearings have no oil hole.
Conn rod side bearings oil hole should be aligned with
oil hole on the conn rod.

6A-54-1.tif

6A-54-2.tif

6A-54-3.tif

6A-54-4.tif

«
...
119
120
121
122
123
...
»

Summary of Contents for NHR 4J Series























































































































































































































































































































































































































Reviews:

No comments

Related manuals for NHR 4J Series

RailKing RKS SD70ACE

Brand: M.T.H. Pages: 12

Brand: Stuart Turner Pages: 20

Brand: Zundapp Pages: 52

Brand: Superrollo Pages: 68

Brand: Kohler Pages: 108

Brand: Lombardini Pages: 50

Brand: Lombardini Pages: 114

Brand: Gude Pages: 52

Brand: Honda Pages: 15

Brand: Honda Pages: 60

Brand: Honda Pages: 133

DSC1-045-100 Series

Brand: Baumuller Pages: 116

Brand: LONCIN Pages: 27

B21 ADAM DRAKE EDITION

Brand: O.S. Speed Pages: 4

Brand: Mitsubishi Heavy Industries Pages: 32

Brand: Xtreme Power Pages: 42

Brand: Wood-mizer Pages: 208

Brand: FAAC Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands