Isuzu NHR 4J Series Workshop Manual Download Page 48 | Manualshive

Page: 48 / 406

background image

00 – 44

SERVICE INFORMATION

Drive Belt Adjustment

Depress the drive belt mid portion with a 98N (10 kg/22
lb) force.
Drive Belt Deflection

mm (in)

10 (0.39)

Check the drive belt for cracking and other damage.
1. Crankshaft damper pulley
2. Generator pulley
3. Cooling fan pulley
4. Oil pump pulley or idler pulley
5. Compressor pulley or idle pulley

Cooling Fan Pulley Drive Belt

Fan belt tension is adjusted by moving the generator.
Depress the drive belt mid portion with a 98N (10 kg/22
lb) force.
1. Crankshaft damper pulley
2. Generator pulley
3. Cooling fan pulley

Compressor Pulley Drive Belt

Move the idler pulley as required to adjust the compressor
drive belt tension.
If the vehicle is equipped with power steering, move the
oil pump as required.
Depress the drive belt mid portion with a 98N (10 kg/22
lb) force.
Belt Deflection

mm (in)

14 - 17 (0.55 - 0.67)

1. Crankshaft damper pulley
2. Oil pump pulley or idler pulley

Power Steering Oil Pump Pulley Drive Belt

Move the oil pump as required to adjust the oil pump drive
belt tension.
On air conditioner equipped models, both drive belts
pulley must always be replaced as a set.
Depress the drive belt mid portion with a 98N (10 kg/22
lb) force.
Belt Deflection

mm (in)

14 - 17 (0.55 - 0.67)

1. Crankshaft damper pulley
2. Oil pump pulley
3. Compressor pulley or idler pulley

0043-1.tif

0043-2.tif

0043-3.tif

0043-4.tif

«
...
46
47
48
49
50
...
»

Summary of Contents for NHR 4J Series























































































































































































































































































































































































































Reviews:

No comments

Related manuals for NHR 4J Series

Brand: ULPOWER Pages: 20

Brand: Zenoah Pages: 20

Brand: hager Pages: 4

Brand: Atlas Copco Pages: 156

MaxxForce DT 10

Brand: Navistar Pages: 109

Brand: Vanguard Pages: 124

Brand: YS Pages: 2

Brand: YS Pages: 2

Brand: YS Pages: 2

Brand: Chicago Pneumatic Pages: 88

Brand: DETROIT Pages: 64

Brand: Detroit Diesel Pages: 224

Brand: Germany Motions Pages: 12

Brand: Motion Pages: 42

Brand: V2 Pages: 16

Brand: Vetus Pages: 76

Brand: O.S. engine Pages: 17

Brand: 3W Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands