Isuzu NHR 4J Series Workshop Manual Download Page 188

Page: 188 / 406

4JB1/4JB1T/4JB1TC/4JG2 – ENGINE 6A1 – 53

INSTALLATION

•

Prepare a solution of 80% engine oil and 20%
molybdenum disulfide.

•

Apply and ample coat of the solution to the teeth of the
oil pump pinion.

5. Oil Pump Assembly

•

Apply engine oil to oil pipe O-ring and insert the O-ring
in O-ring hold on cylinder block.

•

Install oil pump asm with oil pipe in cylinder block and
tighten fixing bolts to the specified torque.

∙

m (kg

∙

m/lb

∙

ft)

19 (1.9/14)

•

Tighten sleeve nut to the specified torque.

∙

m (kg

∙

m/lb

∙

ft)

25 (2.5/18)

4. Oil Pan Assembly

3. Stiffener & Space Rubber

2. Engine Mount Bolts

1. Vacuum Pump Oil Hose

Above works refer to “OIL PAN” Section in this manual.

6A1-53-1.tif

Summary of Contents for NHR 4J Series























































































































































































































































































































































































































Search results

Summary of Contents for NHR 4J Series

Reviews:

Related manuals for NHR 4J Series

Brands by name

Popular brands

Isuzu NHR 4J Series, Workshop Manual

Search results

Summary of Contents for NHR 4J Series

Reviews:

Related manuals for NHR 4J Series

Brands by name

Popular brands