Instramed DUALMAX User Manual Download Page 51

Page: 51 / 219

User manual |

Alarms and limits

• Visual frequency: 2 Hz.
• Frequency of verification of the physiological alarms system by the user:

monthly.

STANDARD ALARM VALUE

The following tables provide the factory default values for the alarm limits:

ECG

NIBP

Bpm Max.

160 BPM

Medium Min.

50 mmHg

Bpm Min.

40 BPM

Initial pressure

140 mmHg

Capnography

Respiration

Max.

60 mmHg

Max.

45 RPM

Min.

21 mmHg

Min.

6 RPM

SpO

ST segment

Answer.

Normal

Max.

10 mm

SPO

Max.

100%

Min.

-10 mm

SPO

Min.

85%

Pulse Max

160

IP (channels 1 and 2)

Pulse Min.

Systole Max.

200 mmHg

Systole Min.

90 mmHg

Temperature (channels 1 and 2)

Diastole Max.

150 mmHg

Max.

38.0°C

Diastole Min.

50 mmHg

Min.

30.0°C

Average Max.

170 mmHg

Average Min

50 mmHg

Technical alarm (medium priority)

Sound and visual signals indicate that the DualMax is not able to accurately monitor

the patient's status. The technical alarm indications are shown in the information bar

(see item "Information bar").
In addition to the technical alarm conditions indicated in the information bar, the

are two more conditions: "bad contact" and "battery charge level" (see following

sections).

Summary of Contents for DUALMAX




























































































































































































































Search results

Summary of Contents for DUALMAX

Reviews:

Related manuals for DUALMAX

Brands by name

Popular brands

Instramed DUALMAX, User Manual

Search results

Summary of Contents for DUALMAX

Reviews:

Related manuals for DUALMAX

Brands by name

Popular brands