Instramed DUALMAX User Manual Download Page 168 | Manualshive

Page: 168 / 219

background image

PC connection

22

Introduction

The DualMax can be connected to a PC, allowing the user access to new functions

as:

•  View, save in external media or print list of the last 100 events.
•  View, save in external media and print ECG activity of the last two hours.
•  Change the operational configurations of the DualMax (only for authorized

technical personnel).

• Check and update firmware version of the equipment (only for authorized

technical personnel).

• Real Time Check: self-diagnosis of defibrillation, battery level, connected pads,

and verification of the device's connection to the mains supply.

Requirements

The DualMax can be connected to a computer through the installation of two pieces

of software: the SoftDEA application and the RTC application. This software is

found on the CD that comes with the device.

To install the SoftDEA application and/or the RTC application, observe the following

requirements:

•  Windows XP, Windows Vista or Windows 7 operating system.
•  CPU of 300 MHz or faster.
•  02 GB free hard disk space.
•  Minimum 512 MB RAM (1 GB recommended).
•  CD or DVD ROM reader unit.

For physical connection to the PC:

• An available USB port.

168

«
...
166
167
168
169
170
...
»

Summary of Contents for DUALMAX




























































































































































































































Reviews:

No comments

Related manuals for DUALMAX

Brand: Labnet Pages: 2

Brand: NEC Pages: 44

Brand: BARKO LOADERS Pages: 85

Pro Vantage 12+ Series

Brand: Ecco Pages: 6

Brand: Garmat Pages: 13

Brand: Gama Sonic Pages: 4

ARIEDO HDC 300W

Brand: GSi Pages: 28

Brand: Nippon Genetics Pages: 14

Groline HI981412

Brand: Hanna Instruments Pages: 44

FUSION Equine DR II

Brand: SOUND Pages: 178

Brand: York Fitness Pages: 18

Brand: 4B Pages: 16

Brand: FitEngine Pages: 68

Brand: olympia electronics Pages: 2

Brand: GVA Lighting Pages: 4

Brand: MSA Pages: 24

Brand: Tektronix Pages: 134

Brand: Otto Bock Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands