Instramed DUALMAX User Manual Download Page 140

Page: 140 / 219

User manual |

Invasive pressure monitoring

140

IP configuration - Principal

1
2

1 - 60 Hz filter

Selection of mains interference filter for both pressure channels.

2 - Channel 1 On/Off

Turns the channel 1 invasive pressure on or off.

3 - Channel 1 scale

Changes the scale of the channel 1 invasive pressure.

4 - Channel 1 clear transducer

Clears the channel 1 invasive pressure transducer.

OBS: this operation must be performed in every new procedure. First

position the transducer and then select “Start”.

5 - Channel 1 reset status

Displays the date of the last reset or the current reset step of the channel 1

transducer.

Summary of Contents for DUALMAX




























































































































































































































Search results

Summary of Contents for DUALMAX

Reviews:

Related manuals for DUALMAX

Brands by name

Popular brands

Instramed DUALMAX, User Manual

Search results

Summary of Contents for DUALMAX

Reviews:

Related manuals for DUALMAX

Brands by name

Popular brands