Instramed DUALMAX User Manual Download Page 187

Page: 187 / 219

User manual |

Care and maintenance

187

Removable battery

Even when disconnected (stand-by), the DualMax executes internal routines

checking the status of the equipment. In spite of this procedure entailing a low

power consumption, the battery charge may be consumed. Therefore, whenever

the device has not been connected to an electric current for more than 20 days, it is

advisable to execute a full battery charge. If this procedure is not performed, there

is a risk of draining the battery and consequently being unable to use the DualMax

in its portable configuration (not connected to the electric current). To recharge the

battery, connect the monitor to charge the battery, connect the monitor to an AC

power source (110 or 220 V outlet) or a DC power source.
There are no restrictions or limitations for using the DualMax while its battery is

being recharged by an AC source or DC External source.
Every battery has a determined lifetime, which is the possible quantity of full charge

and discharge cycles, without loss of performance (see battery specifications in

chapter 8). If the equipment presents a loss in battery performance, please request

a new set to Instramed's technical assistance, To request pieces and services,

please contact Instramed at +55 (51) 3073 8200.

Battery replacement is recommended every 02 (two) years or when the runtime is less

than 01 (one) hour.

Summary of Contents for DUALMAX




























































































































































































































Search results

Summary of Contents for DUALMAX

Reviews:

Related manuals for DUALMAX

Brands by name

Popular brands

Instramed DUALMAX, User Manual

Search results

Summary of Contents for DUALMAX

Reviews:

Related manuals for DUALMAX

Brands by name

Popular brands