manualshive.com logo in svg

Instramed DUALMAX, User Manual

The Instramed DUALMAX User Manual is the essential guide for maximizing your experience with this cutting-edge product. Available for free download at manualshive.com, this comprehensive manual empowers users with detailed instructions, tips, and troubleshooting advice. Unlock the full potential of your Instramed DUALMAX with this user-friendly manual.

Share
Download
background image

User manual | 

Defibrillator mode

70

Using multifunction pads

The use of the multifunction pads (disposable) requires that the operator uses the 

adapter provided (extension cable) in order to connect them to the standard socket 

of the external pads, as described below:

1

 - Connect the AED/pacemaker extension cable to the equipment.

2

 -  Connect the adhesive multifunction pads to the extension cable.

3

 - Remove the multifunction pads’ protective film and apply them to the patient, 

using the same positions recommended for the external pads (Sternum and Apex).

ATTENTION: after opening the wrapping, the pads should be used within 24 

hours.

ATTENTION: in case of use for long periods, the pads should be replaced 

every 24 hours.

Summary of Contents for DUALMAX




























































































































































































































Reviews:

No comments

Related manuals for DUALMAX

Febco 860 Series Maintenance Manual preview
860 Series
Brand: Febco Pages: 12
Yetter 5500 Series Owner'S Manual, Part Identification preview
5500 Series
Brand: Yetter Pages: 16
ACCU-CHECK AVIVA COMBO Reference Manual preview
AVIVA COMBO
Brand: ACCU-CHECK Pages: 104
Badger Meter ER-10 User Manual preview
ER-10
Brand: Badger Meter Pages: 16
G-Lab DR-2 User Manual preview
DR-2
Brand: G-Lab Pages: 16
G&G T3X Quick Start Manual preview
T3X
Brand: G&G Pages: 2
lancer BEV85 Quarterly Service Work Instruction preview
BEV85
Brand: lancer Pages: 3
lancer 2300 Series Installation Manual preview
2300 Series
Brand: lancer Pages: 12
R2 TST Instruction And Maintenance Manual preview
TST
Brand: R2 Pages: 26
Madrigal Stiletto Quick Start Manual preview
Stiletto
Brand: Madrigal Pages: 5
MacDon M1170NT5 Operator'S Manual preview
M1170NT5
Brand: MacDon Pages: 504
IKEA SPOKA Manual preview
SPOKA
Brand: IKEA Pages: 24
CAB PX Q4.3L Service Manual preview
PX Q4.3L
Brand: CAB Pages: 30
zapco AGSP4-SL Owner'S Manual preview
AGSP4-SL
Brand: zapco Pages: 14
Numark NDX500 Operation Manual preview
NDX500
Brand: Numark Pages: 11
Raytec RL F 25 Installation Manual preview
RL F 25
Brand: Raytec Pages: 8
Albrecht Pulsors Repair Instructions preview
Pulsors
Brand: Albrecht Pages: 4
Briteq MICRO BEAMER RGBW Operation Manual preview
MICRO BEAMER RGBW
Brand: Briteq Pages: 16

Brands by name

Popular brands

Load more brands