manualshive.com logo in svg

Instramed DUALMAX, User Manual

The Instramed DUALMAX User Manual is the essential guide for maximizing your experience with this cutting-edge product. Available for free download at manualshive.com, this comprehensive manual empowers users with detailed instructions, tips, and troubleshooting advice. Unlock the full potential of your Instramed DUALMAX with this user-friendly manual.

Share
Download
background image

User manual | 

Defibrillator mode

66

External pads use

1 -

 Verify if the pads are connected to DualMax. If they are not, connect the 

defibrillation cable to the pads socket located on the equipment’s side. (according to 

the image). Press the quick release connector.

2 -

 Take both pads from their base pulling them up and out.

3 -

 Apply the conductive material to the pads' electrodes.

4 -

 Place pads as shown in the image below:

A

B

A - Sternum.
B - Apex.

Summary of Contents for DUALMAX




























































































































































































































Reviews:

No comments

Related manuals for DUALMAX

Hagie 2101 Operator'S Manual Supplement preview
2101
Brand: Hagie Pages: 61
JackJaw 301 Assembly And Operating Instructions preview
301
Brand: JackJaw Pages: 2
JB-Lighting A12 Operating Instructions Manual preview
A12
Brand: JB-Lighting Pages: 60
Bahco BH6 Service Manual preview
BH6
Brand: Bahco Pages: 9
Tascam US-1200 Quick Start Manual preview
US-1200
Brand: Tascam Pages: 8
B-K lighting Union Bollard Installation Instructions preview
Union Bollard
Brand: B-K lighting Pages: 5
B-K lighting RE1 Installation Instructions preview
RE1
Brand: B-K lighting Pages: 4
B-K lighting PS Installation Instructions preview
PS
Brand: B-K lighting Pages: 3
R.M. Young 32500 Quick Start Manual preview
32500
Brand: R.M. Young Pages: 10
Olsen Sprint Quick Operation Manual preview
Sprint
Brand: Olsen Pages: 4
Falcon Dominator Series User, Installation And Servicing Instructions preview
Dominator Series
Brand: Falcon Pages: 31
Fakir HYPO CLEAN Fast User Manual preview
HYPO CLEAN
Brand: Fakir Pages: 22
Fellowes SafeCut Atom User Manual preview
SafeCut Atom
Brand: Fellowes Pages: 20
Halyard MIC-KEY Instructions For Use Manual preview
MIC-KEY
Brand: Halyard Pages: 88
HALDER EH 2B353 Short Instruction Manual preview
EH 2B353
Brand: HALDER Pages: 2
Hällde RG-200 User Instructions preview
RG-200
Brand: Hällde Pages: 40
Hällde RG-400i User Instructions preview
RG-400i
Brand: Hällde Pages: 6
Sagola 4240 Instruction Manual preview
4240
Brand: Sagola Pages: 62

Brands by name

Popular brands

Load more brands