Instramed DUALMAX User Manual Download Page 112

Page: 112 / 219

User manual |

Monitor mode - NIBP

112

Measurement modes

1 - Manual:

Instantaneous measurement of systolic, diastolic and mean pressure.

To activate the manual mode, press NIBP MANUAL MEASUREMENT in the front

panel or in the NIBP Menu Setup, select the Manual Measurement item.

When pressing the NIBP MANUAL MEASUREMENT button while the

monitor is exerting the NIBP measurement, it will immediately interrupt

the measurement.

2 - Long-term automatic:

automatic measurements of systolic, diastolic and mean

pressures. Measurements are automatically repeated during the time set by the

operator.
To activate the automatic mode select the desired time in the Configuration

Menu > NIBP. Interval between measurements can be selected to:

1, 2, 3, 4, 5, 10, 15, 30, 60, 90 minutes.

Interrupting NIBP measurements: to cancel an ongoing pressure

measurement, press “NIBP MANUAL MEASUREMENT”, located in

the equipment’s front panel. The DualMax does not offer a short-term

automatic measurement option.

Summary of Contents for DUALMAX




























































































































































































































Search results

Summary of Contents for DUALMAX

Reviews:

Related manuals for DUALMAX

Brands by name

Popular brands

Instramed DUALMAX, User Manual

Search results

Summary of Contents for DUALMAX

Reviews:

Related manuals for DUALMAX

Brands by name

Popular brands