Instramed DUALMAX User Manual Download Page 161

Page: 161 / 219

User manual |

Printing

161

Configurations

1
2
3

1 - Alarm printing

When the “alarm printing” option is enabled (in the printing setup menu), the

DualMax prints an instant report whenever an alarm goes off.

2 - Shock printing

When the shock printing option is enabled (in the printing setup menu), the

DualMax prints an instant report whenever the equipment identifies shock delivery.

In this report you can see the equipment’s operation mode at the moment of the

defibrillation: MANUAL mode, SYNC mode and AED mode. See the pictures below.

ECG: 60 bpm
SpO2: 96%
Shocks: 0
Time: 01:26
Speed: 25.0 mm/s
Sensitivity: 20 mm/mV
Date: 03/07/19
Time: 12:25

MODE: SYNC

Pads

Summary of Contents for DUALMAX




























































































































































































































Search results

Summary of Contents for DUALMAX

Reviews:

Related manuals for DUALMAX

Brands by name

Popular brands

Instramed DUALMAX, User Manual

Search results

Summary of Contents for DUALMAX

Reviews:

Related manuals for DUALMAX

Brands by name

Popular brands