IBM BladeCenter S SAS RAID Controller Module Installation And User Manual Download Page 179

Page: 179 / 216

|____|_____________|________|_________|________|________|_________|__________|____________|

State: OFN/SN=Offline Non-viable/Service Non-viable

ONF/OFF/SF=Online Failed/Offline Failed/ Service Failed
ONV/OFV/SV= Online Viable/Offline Viable/Service Viable

ONN=Online Non-viable/Pending Non-Viable; one or more drives are missing in this

pool.

The pool state changes to ONV if missing drive(s) comes back to the pool.
The pool state changes to OFN if the user acknowledges the alert.

Drives in primary section:

_________________________________________________________________________________________

| Drive#| E:T |SerialNo| Cap |

Pool

|Usage|State |Mount State|Ctl0|Ctl1|RPM |FW level|

|_______|_____|________|_____|___________|_____|______|___________|____|____|____|________|
| 0

| 2:1 |9QK0SWEJ|698GB|RAID10_Pool| GRP | OK

| Online

| 1

|7200| BC1D

| 1

| 2:2 |9QK0QCJB|698GB|RAID10_Pool| GRP | OK

| Online

| 1

|7200| BC1D

| 2

| 2:3 |9QK0QC50|698GB|RAID10_Pool| GRP | OK

| Online

| 1

|7200| BC1D

|_______|_____|________|_____|___________|_____|______|___________|____|____|____|________|

Drives in secondary section:

_________________________________________________________________________________________

|Usage|State |Mount State|Ctl0|Ctl1|RPM |FW level|

|_______|_____|________|_____|___________|_____|______|___________|____|____|____|________|
| 0

| 1:1 |9QK0SWLM|698GB|RAID10_Pool| GRP | OK

| Online

| 1

|7200| BC1D

| 1

| 1:2 |9QK0V0ZB|698GB|RAID10_Pool| GRP | OK

| Online

| 1

|7200| BC1D

| 2

| 1:3 |9QK0HQ9V|698GB|RAID10_Pool| GRP | OK

| Online

| 1

|7200| BC1D

|_______|_____|________|_____|___________|_____|______|___________|____|____|____|________|

Existing volumes :

__________________________________________________________________________________________

| Volumes

| Cap

| GrpName

| RaidType | Status

|___________________________|__________|_____________|__________|__________________________|
| RAID10_Pool:RAID10_VOL1

| 15GB

| RAID10_Pool | 10

| VBL INI

| RAID10_Pool:RAID10_VOL2

| 15GB

| RAID10_Pool | 10

| VBL INI

| RAID10_Pool:RAID10_VOL3

| 15GB

| RAID10_Pool | 10

| VBL INI

| RAID10_Pool:RAID10_VOL4

| 15GB

| RAID10_Pool | 10

| VBL INI

| RAID10_Pool:RAID10_VOL5

| 15GB

| RAID10_Pool | 10

| VBL INI

| RAID10_Pool:RAID10_VOL6

| 15GB

| RAID10_Pool | 10

| VBL INI

| RAID10_Pool:RAID10_VOL7

| 15GB

| RAID10_Pool | 10

| VBL INI

| RAID10_Pool:RAID10_VOL8

| 15GB

| RAID10_Pool | 10

| VBL INI

|___________________________|__________|_____________|__________|__________________________|

Enter

list drive

and press Enter to list the drive summary for each disk

drive configured in the storage pool. Ensure the mount state of all disk drives
are in the online state.

<CLI> list drive
Current Machine Local Time: 09/15/2009 02:07:53 PM

_________________________________________________________________________________________

|Usage| State | Mount State |Ctl0|Ctl1|RPM |FW level|

|______|___|________|_____|___________|_____|_______|_____________|____|____|____|________|
| 0

|1:1|9QK0SWLM|698GB|RAID10_Pool| GRP | OK

| Online

| 1

|7200| BC1D

| 1

|1:2|9QK0V0ZB|698GB|RAID10_Pool| GRP | OK

| Online

| 1

|7200| BC1D

| 2

|1:3|9QK0HQ9V|698GB|RAID10_Pool| GRP | OK

| Online

| 1

|7200| BC1D

| 3

|1:4|9QK0QCGS|698GB| --

| UNA | OK

| Online

| 1

|7200| BC1D

| 4

|1:5|9QK0HQ74|698GB| --

| UNA | OK

| Online

| 1

|7200| BC1D

| 5

|1:6|9QK0QCEQ|698GB| --

| UNA | OK

| Online

| 1

|7200| BC1D

| 6

|2:1|9QK0SWEJ|698GB|RAID10_Pool| GRP | OK

| Online

| 1

|7200| BC1D

| 7

|2:2|9QK0QCJB|698GB|RAID10_Pool| GRP | OK

| Online

| 1

|7200| BC1D

| 8

|2:3|9QK0QC50|698GB|RAID10_Pool| GRP | OK

| Online

| 1

|7200| BC1D

| 9

|2:4|9QJ1NG5W|931GB| --

| UNA | OK

| Online

| 1

|7200| BC1D

| 10

|2:5|9QK0SWLY|698GB| --

| UNA | OK

| Online

| 1

|7200| BC1D

| 11

|2:6|9QK0QC85|698GB| --

| GLS | OK

| Online

| 1

|7200| BC1D

|______|___|________|_____|___________|_____|_______|_____________|____|____|____|________|

Drive E:T is Enclosure:Tray; tray numbers start at 1, and tray 1 is the uppermost tray.

Usage:

UNA=unassigned

GRP/SGR=current/stale group member

Chapter 11. Troubleshooting and support

169

Summary of Contents for BladeCenter S SAS RAID Controller Module

























































































































































































































Search results

Summary of Contents for BladeCenter S SAS RAID Controller Module

Reviews:

Related manuals for BladeCenter S SAS RAID Controller Module

Brands by name

Popular brands

IBM BladeCenter S SAS RAID Controller Module, Installation And User Manual

Search results

Summary of Contents for BladeCenter S SAS RAID Controller Module

Reviews:

Related manuals for BladeCenter S SAS RAID Controller Module

Brands by name

Popular brands