6-37
FUSE
NO.11
CN-36-1
11
4
16
GND
CN-21
VCC
GND
MOTOR DRIVE+
MOTOR DRIVE-
MOTOR DRIVE SIG
FEED BACK
FEED BACK
N.C
WIPER CUT SW
INT. SIG
WASHER SIG.
WASHER P/P
CONTINUE 24V
3
2
1
4
5
6
WIPER MOTOR
3
5
4
2
6
M
CN-17
CN-141
WIPER MOTOR CONTROLLER
3
2
1
4
5
6
7
8
3
2
1
4
5
6
7
8
9
10
11
12
13
WASHER PUMP
M
CN-22
WIPER CUT SW
CS-53
2
1
FUSE
NO.21
CN-5
FUSE
NO.6
18
19
15
16
17
21
20
CN-376
MEMBRANE CONTROLLER
1
2
DO-5
1
2
3
4
5
6
7
8
9
10
11
12
CAN_LO(2)
INT WIPER
NC
13
15
NC
18
TRVEL ALARM
26
27
CAN_HI(2
)
HEAD LIGHT
GND
WIPER
CABIN LIGHT
NC
WORK LIGHT
NC
NC
BEACO LAMP SW
IG 24V
WASHER
34
14. WHEN STARTING SWITCH IS TURNED ON, WIPER MOTOR DOES NOT OPERATE
·
Before disconnecting the connector, always turn the starting switch OFF.
·
Before carrying out below procedure, check all the related connectors are properly inserted and the fuse
No. 6, 11 and 21 is not blown out.
·
After checking, insert the disconnected connectors again immediately unless otherwise specified.
Defective wiper
cut switch
Short circuit in
wiring harness or
poor contact
between CN-141
(11)- CS-53
Defective
membrane
controller
1) Recheck fuse
No.11
2) Disconnection in
wiring harness or
poor contact
between
CN-376(1)-Fuse
Defective membrane
controller
1) Recheck fuse
No.6
2) Disconnection
in wiring harness
or poor contact
between
CN-141(7)-Fuse,
CN-21(4)-Fuse
1) Recheck fuse
No.21
2) Disconnection
CN-141(6)-Fuse
ⓑ
Disconnection in
wiring harness or
poor contact
Defective wiper
motor
Defective wiper
motor controller
Replace
Repair or replace
(after clean)
Replace
Replace
Repair or replace
(after clean)
Replace
Replace
Repair or replace
(after clean)
Replace
Repair or replace
(after clean)
Repair or replace
(after clean)
Replace
Replace
Cause
Remedy
ⓐ
Check voltage
between CN-376
(1) and chassis
Check valtage
between CN-141
(11) and chassis
Check operation
wiper cut switch
Check operation
of membrane
controller LED
ON.
Check voltage
CN-141 (6) and
chassis
Check operation
of wiper motor
and controller
check voltage
CN-141 (7) and
chassis, CN-21
(4) and chassis
Check voltage between
CN-376 (3) and chassis
Check voltage CN-376
(11) and chassis
Check voltage CN-376
(12) and chassis
ⓐ
ⓑ
Check wiper
motor resistance
between CN-21
(2)-CN-21 (6)
Check continuity
between
CN-141 (2)-CN-376 (3),
CN-141 (9)-CN-376 (11),
CN-141 (10)-CN-376 (12),
CN-141 (5)-Chassis ,
CN-141 (1)-CN-21 (5),
CN-141 (3)-CN-21 (6),
CN-141 (4)-CN-21 (2),
CN-141 (13)-CN-21 (3)
Intermittent
Starting switch : OFF
Voltage : 20~30V
Resistance : 3~4
Ω
Starting switch : ON
Voltage : 20~30V
Washing
Sarting switch : ON
Voltage : 0~1V
YES
YES
NO
NO
YES
YES
YES
YES
YES
YES
YES
NO
NO
NO
NO
NO
NO
Front sliding door
open-close
Front sliding door-close
Voltage : 4~5V
Starting switch : ON
Push wiper switch button
Starting switch : ON
Vottage : 20~30V
NO
130ZF6ES15
Summary of Contents for HX130 LCR
Page 11: ...1 1 SECTION 1 GENERAL Group 1 Safety Hints 1 1 Group 2 Specifications 1 10 ...
Page 174: ...4 5 MEMORANDUM HYUNDAI HEAVY INDUSTRIES CO LTD CONSTRUCTION EQUIPMENT DIV ...
Page 536: ...8 108 125LCR8TM30 Turn casing 1 upside down and remove oil seal 3 using jig 29 ...
Page 566: ...8 138 Remove lock nut 22 and then boot 23 14 36078RL14 2507ARL10 ...