Honeywell FMZ Series Pilot'S Manual Download

Page: 373 / 542

Flight Management System (FMS) for the Agusta AW139/AB139 Helicopter

A28--1146--181

REV 3 Mar 2009

7-7

Flight Plan

Honeywell International Inc. Do not copy without express permission of Honeywell.

—

Direct--to does not result in a discontinuity even though several

waypoints are deleted or a single waypoint is added.

—

When an airway is inserted in the flight plan, there is no

discontinuity since the pilot has to specify the beginning and end

points.

—

The INTERCEPT function does not create a discontinuity before

or after the intercept point. When choosing the heading--to

intercept option, a fly heading select leg is inserted disengaging

the FMS when the leg is sequenced.

Alternate Origin

-- The alternate origin is the destination of the

primary flight plan. No alternate flight plan is specified until the

primary destination has been specified. Changing the primary

destination clears the alternate flight plan because the alternate

origin changes.

Alternate Waypoints

-- Alternate waypoints apply only to the

alternate portion of the flight plan. The FMS guidance is not engaged

until the pilot selects the alternate destination. When the alternate

portion of the flight plan is enabled, the corresponding waypoints are

incorporated into the primary portion of the flight plan. At that point,

all active flight plan rules apply.

Alternate Destination

-- The alternate destination is entered when

defining a flight plan to an alternate. Like the primary flight plan, the

alternate destination is entered as the final waypoint to close out the

alternate flight plan.

Climb Constraints

-- Climb constraints are altitude and speed

constraints associated with waypoints in the climb or cruise portion

of the flight plan. Altitude constraints are AT, AT or ABOVE, or AT

or BELOW. For example, an entry of 10000A (

following the

altitude) indicates AT or ABOVE. An entry of 10000B (

following

the altitude) indicates AT or BELOW. An entry of 10000 (no letter

following the altitude) indicates AT. Climb speed constraints are

observed by the FMS until the waypoint containing the constraint is

passed.

Speed Limit

-- An example of speed limits is the 250 knots (kts)

below 10,000 feet (ft) limit entered during performance initialization.

Other limits are imposed by the airframe such as V

Speed Schedule

-- Speed schedules are the default speeds used

by the FMS for the departure, climb, cruise, descent, approach and

go--around phase of flight. Speed schedules are defined during

performance initialization.

Summary of Contents for FMZ Series































































































































































































































































































































































































































































































































































Search results

Summary of Contents for FMZ Series

Reviews:

Related manuals for FMZ Series

Brands by name

Popular brands

Honeywell FMZ Series, Pilot'S Manual

Search results

Summary of Contents for FMZ Series

Reviews:

Related manuals for FMZ Series

Brands by name

Popular brands