manualshive.com logo in svg

H3C XE 200/2000 IP, Operation Manual

The H3C XE 200/2000 IP is a cutting-edge networking device that offers superior performance and reliability. Its operation manual is available for free download from manualshive.com, providing users with comprehensive instructions and guidance to optimize their experience with this exceptional product.

Share
Download
background image

Operation Manual – Feature 
H3C XE 200/2000 IP PBX 

Chapter 4  VoIP RADIUS Accounting Configuration

 

4-4 

4.3.5  Configuring a Timeout Timer for Sending a Request to a RADIUS 
Server 

When the XE IP PBX sends an authentication request to the RADIUS server, the 

system starts a timeout timer for the response (to the authentication request, for 

example). After the timer expires, the system retransmits the request and resets the 

timer. 

Perform the following configuration in system view. 

Table 4-5 

Configure the timeout timer for the XE IP PBX to send authentication request 

packets to the RADIUS server 

Operation 

Command 

Configure the timeout timer for the XE IP 
PBX to send an authentication request 
packet to the RADIUS server.  

radius timer response-timeout

 

seconds

 

Restore the timeout timer to the default 
value.  

undo radius timer response-timeout

 

 

By default, the interval for the XE IP PBX to send authentication request packets to a 

RADIUS Server is 5 seconds. The interval you can set ranges from 1 to 300 seconds.  

4.3.6  Specifying a Source IP address for the RADIUS Packets to be 
Transmitted 

You may specify a source IP address for the RADIUS packets sent from different 

interfaces on the XE IP PBX. In this way, the RADIUS server will contact the XE IP PBX 

only at that IP address. 

An RADIUS server requires the administrator to register all the RADIUS clients, which 

are determined on the basis of source IP address. Therefore, the interfaces with 

different IP addresses on the same XE IP PBX will be regarded by the RADIUS server 

as different clients. Whenever the RADIUS server receives a packet carrying an 

unregistered source IP address, it will regarded the packet as illegal and hence make 

no processing on it. For this reason, you may configure a source IP address for the 

transmitted RADIUS packets on the XE IP PBX to get free of the work of registering the 

IP addresses for all the interfaces on the XE IP PBX with the server. 

 

Summary of Contents for XE 200/2000 IP



































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for XE 200/2000 IP

Panasonic KX-TDA100BX Service Manual preview
KX-TDA100BX
Brand: Panasonic Pages: 96
Yeastar Technology MyPBX Standard User Manual preview
MyPBX Standard
Brand: Yeastar Technology Pages: 152

Brands by name

Popular brands

Load more brands