manualshive.com logo in svg

GSi EVO-50, Construction Manual, Page: 91 / 222

Share
Download
GSi EVO-50 Construction Manual Download Page 91

Chapter 7: Door Assemblies

Installing the Inside Door Panels

IMPORTANT:

The inner door panels (34 and 35) must seat on the bearing pins and lock over latch bar

holders for the door panels to close correctly. DO NOT fill the bin until the door panels
have been installed correctly.

NOTE:

Adjust the panel hinges (40) if needed to align the door on the bearing pins (38).

1. Install four shims (46) and six door frame panel hinges (47) to the left side of the inner door frame

weldment (33) using twelve 7/16" x 3" flange bolts (2), 7/16" flat washers (20) and 7/16" hex nuts
(22).

NOTE:

At hinge locations, replace the 7/16" x 2" flange bolts used when installing the jamb plates.

2. Align the hinges (40) on the bottom door assembly with the bottom set of panel hinges (47) and

install using three 3/8" x 4-1/2" HHCS bolts (10), 3/8" flat washers (15) and 3/8" lock nuts (23).

3. Align the hinges (40) on the top door assembly with the top set of panel hinges (47) and install using

three 3/8" x 4-1/2" HHCS bolts (10), 3/8" flat washers (15) and 3/8" lock nuts (23).

4. After the doors are seated on the bearing pins (38) and seal when closed, fully tighten all the bearing

pins (38) and latch bar holders.

5. Install foam seal (30) along the outside edge of the inner door frame weldment (33) where the door

meets the frame.

Figure 7-16

Installing the top and bottom inside door panels - 2 post

2

7/16" x 3" flange bolt (S-8316)

33

Inner door frame weldment (NCWT0732-BS)

10

3/8" x 4-1/2" HHCS bolt (S-1443)

35

Bottom inner door panel (NCWT0462)

15

3/8" flat washer (S-248)

38

Bearing pins (WD-6224)

20

7/16" flat washer (S-8612)

40

Inside/outside hinge weldment (NCWT0103)

22

7/16" hex nut (S-8479)

46

Hinge shim (NCWT0495)

23

3/8" lock nut (S-7383)

47

Inner door hinge housing (NCWT0801)

30

Foam seal (S-8610)

PNEG-5490D-2X

90' Diameter EVO-50 Beam 2X Bin

91

Summary of Contents for EVO-50































































































































































































































Reviews:

No comments