GSi EVO-50 Construction Manual Download Page 44

Page: 44 / 222

Chapter 4: Assembling the Sidewall Sheets

Caulking and Assembling the Double Laminated Sheets

Each outer sidewall sheet (1O) must be layered and caulked prior to assembling sidewall sheet seams
together.

The inner sidewall sheets (1I) do not have any caulking.

1. Apply a vertical strip of caulk (2) between the outside edge of the outer sheet (1O) and first row of

holes and another vertical strip (2) between the first and second row of holes.

2. Apply a horizontal strip of caulk (3) between the edge of the sheet and first horizontal seam hole.

3. Apply a strip of caulking (4) around the stiffener holes on the outer sheet (1O).

4. Apply a horizontal strip of caulk (5) between the overlapping vertical seam edge and first horizontal

seam hole at both the sides of the outer sheet (1O).

NOTE:

Always assemble the sidewall sheets with the overlap in the same direction.

Figure 4-8

Caulking between double laminated sidewall sheets

Inner sidewall sheet

1/8" x 1/4" caulking strip (horizontal) (S-4458)
(For 14-10 gauge laminates: 13")
(For 9-5 gauge laminates: 18")

1O Outer sidewall sheet

1/8" x 1-1/4" caulking strip (stiffener hole) (S-10716)

1/8" x 1/4" caulking strip (vertical)
(S-4458)

1/8" x 1-1/4" caulking strip (horizontal) (S-10716)
(For 14-10 gauge laminates: 7.5" to 13")
(For 9-5 gauge laminates: 10" to 18")

PNEG-5490D-2X

90' Diameter EVO-50 Beam 2X Bin

Summary of Contents for EVO-50































































































































































































































Search results

Summary of Contents for EVO-50

Reviews:

GSi EVO-50, Construction Manual, Page: 44 / 222

Search results

Summary of Contents for EVO-50

Reviews: