manualshive.com logo in svg

GSi EVO-50, Construction Manual, Page: 161 / 222

Share
Download
GSi EVO-50 Construction Manual Download Page 161

Chapter 8: Roof Assembly

Assembling the Lower Stand-Off Bracket to the Outer Center Collar

There will be eight lower stand-off support brackets that are needs to be assembled to the outer center
collar before it is lifted onto the roof with the center pole.

Before You Begin

Make sure that the outer center collar is secured properly on the stands or suitable blocks.

1. Locate a set of four holes on the top flange of the outer center collar (45) and place the lower

stand-off support bracket (111).

2. Install the lower stand-off support bracket (111) to the outer center collar (45) using 3/8" x 1-1/2"

flange bolt (1) and 3/8" flange nuts (15).

3. Repeat the procedure to continue installing all the remaining lower stand-off brackets (111) to the

outer center collar (45).

4. Tighten all the hardware to the recommended specifications. See

Bolt Torque Specifications, page

26

.

Figure 8-22

Assembling the lower stand-off brackets to the outer center collar

1

3/8" x 1-1/2" flange bolt with sealing washer
(S-7488)

45

Outer center collar (CTR-2224-BS)

15

3/8" flange nut (S-9426)

111

Lower stand-off support bracket
(CTR-1559-BS)

PNEG-5490D-2X

90' Diameter EVO-50 Beam 2X Bin

161

Summary of Contents for EVO-50































































































































































































































Reviews:

No comments