manualshive.com logo in svg

GSi EVO-50, Construction Manual, Page: 171 / 222

Share
Download
GSi EVO-50 Construction Manual Download Page 171

Chapter 8: Roof Assembly

6. After the roof panels are installed to the rafters, position a lower roof panel (114) to the immediate

left of the previously installed lower panels (114).

NOTE:

The lower panels (114) must be positioned in the gap below the upper roof panel (116).

7. Slide a rib cap (117) over the rib of the two lower panels (114), where the upper panel (116) and the

lower panels (114) overlap. Make sure the rib cap (117) fits in the slot of the upper roof panel (116)
and the flanges of the rib cap (117) are positioned under the upper roof panel (116).

8. Install 5/16" x 1" flange bolts (2) and 5/16" flange nuts (19) to secure the lower roof panels (114) and

rib cap (117) with the upper roof panel (116).

NOTE:

Make sure to apply the rope caulk (122) around the perimeter of the rib cap (117) for sealing
before installing flange bolts (2) and nuts (19).

9. Working in a

counter-clockwise

direction, fill in the adjacent gaps by installing two additional lower

roof panels (114) and an upper roof panel (116) overlapping each panel on the left. Adjust the roof
panels as needed.

NOTE:

Make sure to tuck one roof panel per gap under the previously installed roof panel, by slightly
lifting the upper rib (135) of the previously installed panel and allowing the lower rib (136) of
the new roof panel to be tucked under the previous panel.

10.Install 5/16" x 1" flange bolts (2) and 5/16" flange nuts (19) securing the overlapping of upper panels

(116) with lower panels (114).

11.Install 5/16" x 1" flange bolts (2) and 5/16" flange nuts (19) along the ribs (135 and 136) of each

lower panel (114) and upper panel (116) to secure them.

PNEG-5490D-2X

90' Diameter EVO-50 Beam 2X Bin

171

Summary of Contents for EVO-50































































































































































































































Reviews:

No comments