manualshive.com logo in svg

GSi EVO-50, Construction Manual, Page: 120 / 222

Share
Download
GSi EVO-50 Construction Manual Download Page 120

Chapter 7: Door Assemblies

Assembling the Outer Door

The outer door must be assembled before it can be installed to the column weldments.

1. Attach the middle reinforcement channel (51) at the same time as the hold-back plate (76) to the

middle of the outer door cover (48) using six 5/16" x 1" flange bolts (8) and 5/16" flange nuts (26).

NOTE:

Make sure to install the channel (51) on the inside and hold-back plate (76) on the outside of
the outer door cover (48).

2. Install the top and bottom reinforcement channels (51) at the same time as the handle mounting

brackets (49) and cover hinge brackets (50) to the outer door cover (48) using twelve 5/16" x 1"
flange bolts (8) and 5/16" flange nuts (26).

NOTE:

Make sure to install the channels (51) on the inside and the handle mounting brackets (49)
and cover hinge brackets (50) on the outside of the outer door cover (48).

3. Install the door latch rod (52) to the handle mounting brackets (49) using four 5/16" x 1-1/2" flange

bolts (11) and 5/16" flange nuts (26).

NOTE:

Install the flange bolts (11) with bolt head on the outside of the door latch rod (52).

4. Apply decals (DC-GBC-2A and DC-GBC-2S) to the outside of the outer door cover (48).

Figure 7-44

Assembling the outer door cover

8

5/16" x 1" flange bolt with sealing washer (S-10260)

50

Door cover hinge bracket (NCWT0170)

11

5/16" x 1-1/2" flange bolt (S-10185)

51

Reinforcement channel (NCWT0162)

26

5/16" flange nut (S-3611)

52

Door latch rod (WD-6284)

48

Outer door cover (NCWT0173D)

76

Hold-back plate (NCWT0699)

49

Handle mounting bracket (WD-6287)

120

PNEG-5490D-2X

90' Diameter EVO-50 Beam 2X Bin

Summary of Contents for EVO-50































































































































































































































Reviews:

No comments