manualshive.com logo in svg

GSi EVO-50, Construction Manual, Page: 47 / 222

Share
Download
GSi EVO-50 Construction Manual Download Page 47

Chapter 4: Assembling the Sidewall Sheets

Caulking and Assembling the Triple Laminated Sheets

Each outer sidewall sheet (1O) must be layered and caulked prior to assembling sidewall sheet seams
together.

The inner sidewall sheets (1I) do not have any caulking.

1. Apply a vertical strip of caulk (2) between the outside edge of the outer sheet (1O) and first row of

holes and another vertical strip (2) between the first and second row of holes.

2. Apply a horizontal strip of caulk (3) between the edge of the sheet and second horizontal seam hole.

3. Apply a strip of caulking (4) around the stiffener holes on the outer sheet (1O).

4. Apply a horizontal strip of caulk (5) between the overlapping vertical seam edge and second

horizontal seam hole at both the sides of the outer sidewall sheet (1O) and middle sidewall sheet
(1M).

NOTE:

Always assemble the sidewall sheets with the overlap in the same direction.

Figure 4-11

Caulking between triple laminated sidewall sheets

1I

Inner sidewall sheet

3

1/8" x 1/4" caulking strip (horizontal) (S-4458)
(For 14-10 gauge laminates: 13")
(For 9-5 gauge laminates: 18")

1M Middle sidewall sheet

4

1/8" x 1-1/4" caulking strip (stiffener hole) (S-10716)

1O Outer sidewall sheet

5

1/8" x 1-1/4" caulking strip (horizontal) (S-10716)
(For 14-10 gauge laminates: 7.5" to 13")
(For 9-5 gauge laminates: 10" to 18")

2

1/8" x 1/4" caulking strip (vertical) (S-4458)

PNEG-5490D-2X

90' Diameter EVO-50 Beam 2X Bin

47

Summary of Contents for EVO-50































































































































































































































Reviews:

No comments