GSi EVO-50 Construction Manual Download Page 184

Page: 184 / 222

Installing the Upper Stand-Off Support Brackets

Eight upper stand-off support brackets are attached to the top panels and allow support for a conveyor or
catwalk system.

1. Locate the eight sets of four holes in the top panels (121), and place a gasket (123) over each set of

eight holes, where the upper stand-off support brackets (112) will be installed.

2. Position one upper stand-off bracket (112) over each gasket (123) and align the holes.

3. Install 3/8" x 1-1/2" flange bolts (1) and 3/8" flange nuts (15) to secure the upper stand-off support

brackets (112), gaskets (123) and lower stand-off support brackets (111) together with the top
panels (121).

NOTE:

Make sure the end lines in the stand-off brackets (111 and 112) are vertical.

Figure 8-42

Installing the upper stand-off support brackets

3/8" x 1-1/2" flange bolt with sealing washer (S-7488)

112

Upper stand-off support bracket
(CTR-1559-BS)

3/8" flange nut (S-9426)

121

Top panel (CTR-1585)

111

Lower stand-off support bracket (CTR-1559-BS)

123

Gasket (S-10378)

4. Tighten all the hardware to the recommended torque specifications. See

Bolt Torque Specifications,

page 26

184

PNEG-5490D-2X

90' Diameter EVO-50 Beam 2X Bin

Summary of Contents for EVO-50































































































































































































































Search results

Summary of Contents for EVO-50

Reviews:

GSi EVO-50, Construction Manual, Page: 184 / 222

Search results

Summary of Contents for EVO-50

Reviews: