Home
/
GSi
/
EVO-50
/
Construction Manual

GSi EVO-50, Construction Manual, Page: 139 / 222

Share

Page: 139 / 222

GSi EVO-50 Construction Manual Download Page 139

Chapter 8: Roof Assembly

About Temperature Cable Brackets and A-Frame Assemblies

Temperature cable bracket installation locations must be considered prior to assembling the A-frames.

Installation Locations for Temperature Cable Brackets

Before assembling the A-frames, you must know the installation locations of the temperature cable
brackets within the A-frame assemblies. Temperature cable brackets are installed at the same time as the
purlin clips are installed.

This information is provided solely for the purpose of facilitating proper support bracket placement. It is
fully the responsibility of the dealer, customer, contractor, or said agent of such parties to confirm the
details of the system to be used. GSI is not responsible for the effectiveness or performance of any
temperature cable monitoring system or layout.

IMPORTANT:

Temperature cable brackets must be installed at the specified locations as shown below.

Any variation from this pattern or cable quantity shown must be reviewed by GSI
engineering. This must be reviewed well in advance of the bin order.

Lifting Sequence for the A-Frame Assemblies

The roof structure layout consists of standard A-frame assemblies and A-frame assemblies with
diagonal bracing that are installed in a specific sequence to evenly distribute the weight as they are being
installed.

The A-frames with diagonal bracing are strategically spaced around the diameter of the bin and are the
first A-frames to be installed. The A-frame assemblies can be installed in the order as shown in the figure
below. A-frames are installed across from each other to keep the weight distributed evenly during
installation.

Tip

During the A-frame assembly, label each A-frame assembly according to the order it is to be installed.

PNEG-5490D-2X

90' Diameter EVO-50 Beam 2X Bin

139

«
...
137
138
139
140
141
...
»

Summary of Contents for EVO-50































































































































































































































Reviews:

No comments