GSi EVO-50 Construction Manual Download Page 143

Page: 143 / 222

Chapter 8: Roof Assembly

3. Install a quick link (130) to each temperature cable assembly (44) to support the temperature

cables.

IMPORTANT:

Do not attach weights to the temperature cables; secure the bottom of cables to the

floor with light twine. No roof rafter shall support more than one cable.

Figure 8-10

Installing the supplier quick link to the temperature cable bracket

Temperature cable assembly (CRP-6166)

130

Supplier quick link

128

Roof rafter

4. Locate the center collar (45) temperature cable hole (131) and install a supplier quick link (130),

allowing for the installation of a temperature cable at this location.

Figure 8-11

Installing the supplier quick link to the center collar (view from bottom side of center collar)

Outer center collar (CTR-2224-BS)

131

Temperature cable hole

130

Supplier quick link

PNEG-5490D-2X

90' Diameter EVO-50 Beam 2X Bin

143

Summary of Contents for EVO-50































































































































































































































Search results

Summary of Contents for EVO-50

Reviews:

GSi EVO-50, Construction Manual, Page: 143 / 222

Search results

Summary of Contents for EVO-50

Reviews: