GSi EVO-50 Construction Manual Download Page 181

Page: 181 / 222

2. Align the holes on the first top panel (121) with the holes in the center collar channel brackets (120)

and the inner center collar flange (119).

3. Install 3/8" x 1" flange bolts (3) and 3/8" flange nuts (15) only to the holes at one end to secure the

first top panel (121) with the center collar channel bracket (120).

NOTE:

Leave the flange bolts (3) hand tight to remove it later when tucking the last top panel (121)
under the first top panel (121).

Figure 8-39

Installing the first top panel

3/8" x 1" flange bolt with sealing washer (S-7487)

120

Center collar channel bracket
(CTR-1580)

3/8" flange nut (S-9426)

121

Top panel (CTR-1585)

119

Inner center collar (CTR-1581-BS)

PNEG-5490D-2X

90' Diameter EVO-50 Beam 2X Bin

181

Summary of Contents for EVO-50































































































































































































































Search results

Summary of Contents for EVO-50

Reviews:

GSi EVO-50, Construction Manual, Page: 181 / 222

Search results

Summary of Contents for EVO-50

Reviews: