Home
/
GSi
/
EVO-50
/
Construction Manual

GSi EVO-50, Construction Manual, Page: 114 / 222

Share

Page: 114 / 222

GSi EVO-50 Construction Manual Download Page 114

Chapter 7: Door Assemblies

Installing the Bearing Pins

The bearing pins (38) are used to align the inside panels correctly with the door frame weldment.

Install eight bearing pins (38) to the inner door frame weldment (33) using 5/16" x 1-1/2" HHCS bolts (5),
5/16" flat washers (18) and 5/16" flange nuts (26).

NOTE:

Do not fully tighten bearing pins (38) until the inside doors are installed and adjusted.

Figure 7-39

Installing the bearing pins

5

5/16" x 1-1/2" HHCS bolt (S-2741)

33

Inner door frame weldment (NCWT0763-BS) (2-post)

18

5/16" flat washer (S-845)

Inner door frame weldment (NCWT0779-BS) (3-post)

26

5/16" flange nut (S-3611)

38

Bearing pins (WD-6224)

114

PNEG-5490D-2X

90' Diameter EVO-50 Beam 2X Bin

«
...
112
113
114
115
116
...
»

Summary of Contents for EVO-50































































































































































































































Reviews:

No comments