manualshive.com logo in svg

GSi EVO-50, Construction Manual, Page: 136 / 222

Share
Download
GSi EVO-50 Construction Manual Download Page 136

Chapter 8: Roof Assembly

Connecting the Tension Member to the Eave Bracket

Tension members are installed to the eave bracket around the inside of the bin.

Before You Begin

Make sure all the eave brackets and eave angles are installed.

What You Should Know

IMPORTANT:

Install bolts with bolt head on the backside of the eave bracket as shown.

1. Lift and support one tension member (29) against the inside mating surface and another tension

member (29) against the outside mating surface of the eave bracket (23).

2. Install 1/2" x 2-1/4" HHCS bolts (6) and 1/2" flange nuts (17) to each end of the tension members

(29).

3. Tighten all the hardware to the recommended torque specifications. See

Bolt Torque Specifications,

page 26

.

Figure 8-5

Installing the tension member to the eave bracket

6

1/2" x 2-1/4" HHCS bolts (S-7894)

27

Eave angle (CTR-0721)

17

1/2" flange nut (S-10253)

29

Tension member (CTR-2190)

23

Eave bracket (CTR-2174-BS)

After You Finish

Repeat this process to install the remaining tension members to the eave bracket.

136

PNEG-5490D-2X

90' Diameter EVO-50 Beam 2X Bin

Summary of Contents for EVO-50































































































































































































































Reviews:

No comments