manualshive.com logo in svg

Epson S1C33L26, Technical Manual

The Epson S1C33L26 Technical Manual is here to assist you in understanding the functionality and features of this incredible product. Easily accessible for download, for free, from our website, it provides comprehensive instructions and insights to maximize your experience with the Epson S1C33L26.

Share
Download
background image

26  LCD CONTROLLER (LCDC)

S1C33L26 TECHNICAL MANUAL

 

Seiko Epson Corporation 

26-11

FPSHIFT mask for monochrome LCD panel

 

When color passive panel is selected (COLOR/LCDC_DISPMOD register = 1), the FPSHIFT clock is output 
during the horizontal display period (HDP) and it stops during the horizontal non-display period (HNDP) as 
shown in Figures 26.5.2.2 to 26.5.2.6.

 

When monochrome passive panel is selected (COLOR = 0), the FPSHIFT clock does not stop even in the hori-
zontal non-display period by the default setting. To stop the FPSHIFT clock during the horizontal non-display 
period, set FPSHIFT_MSK/LCDC_DISPMOD register to 1.

Note:  When using an STN panel, the registers for setting the HR-TFT timing parameters must be set to 

0x0.

HR-TFT Panel Timing Parameters

26.5.3  

The HR-TFT panel timing parameters shown in Figures below can be set using the LCDC control registers.

FPLINE (LP)

HPW

HPS

HDPS

HT

FPFRAME (SPS)

VT

VDPS

VDP

HDP

VPS

VPW

Non display period

Display period

5.3.1  HR-TFT Panel Timing Parameters

Figure 26.

D1

D2

D319

D320

FPFRAME (SPS)

FPLINE (LP)

FPLINE (LP)

FPSHIFT (DCLK)

FPDAT[23:0]

FPDRDY (DEN)

TFT_CTL3 (SPL)

TFT_CTL1 (CLS)

TFT_CTL0 (PS)

TFT_CTL2 (REV)

TFT_CTL1 pulse start offset

TFT_CTL2 delay

TFT_CTL1 pulse stop offset

TFT_CTL0 pulse start offset

TFT_CTL0 pulse stop offset

HT

HDPS

HDP

HPS

FPFRAME pulse 
start offset

VPS

VPW

FPFRAME pulse stop offset

HPW

Horizontal timing

Summary of Contents for S1C33L26



















































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for S1C33L26

ICM Controls ICM330 Manual preview
ICM330
Brand: ICM Controls Pages: 2
ICM Controls ICM2909 Manual preview
ICM2909
Brand: ICM Controls Pages: 2
Lawler 804 Installation & Maintenance Manual preview
804
Brand: Lawler Pages: 5
Taylor i16 Operating Manual preview
i16
Brand: Taylor Pages: 34
Mita WP3000 Manual preview
WP3000
Brand: Mita Pages: 7
Toho Electronics TTM-339 Operation Manual preview
TTM-339
Brand: Toho Electronics Pages: 32
SAMES KREMLIN LP 6 - 0.5/4 Translation From The Original Manual preview
LP 6 - 0.5/4
Brand: SAMES KREMLIN Pages: 5
NEC V850E/RS1 User Manual preview
V850E/RS1
Brand: NEC Pages: 852
tecatlantis LUMINUS Operating Manual preview
LUMINUS
Brand: tecatlantis Pages: 68
AUMA PROFOX PF-M100X Manual preview
PROFOX PF-M100X
Brand: AUMA Pages: 56
SUNWIND DR2210N -DDB User Manual preview
DR2210N -DDB
Brand: SUNWIND Pages: 53
Xylem McDonnel & Miller 157S-RBP-MD Instruction Manual preview
McDonnel & Miller 157S-RBP-MD
Brand: Xylem Pages: 8
digitalview 417100041-3 Instructions Manual preview
417100041-3
Brand: digitalview Pages: 30
Rexroth Indramat DURADRIVE SYSTEM200 Project Planning Manual preview
DURADRIVE SYSTEM200
Brand: Rexroth Indramat Pages: 86
TEXA 10TD088A0 Manual preview
10TD088A0
Brand: TEXA Pages: 185
gefran 1200-RD00-00-0 Series Quick Start Manual preview
1200-RD00-00-0 Series
Brand: gefran Pages: 6
CS Technologies ACE-CONVERTER Installation Manual preview
ACE-CONVERTER
Brand: CS Technologies Pages: 4
Marthon AVR SE350 Instruction Manual preview
AVR SE350
Brand: Marthon Pages: 7

Brands by name

Popular brands

Load more brands