manualshive.com logo in svg

Epson S1C33L26, Technical Manual

The Epson S1C33L26 Technical Manual is here to assist you in understanding the functionality and features of this incredible product. Easily accessible for download, for free, from our website, it provides comprehensive instructions and insights to maximize your experience with the Epson S1C33L26.

Share
Download
background image

26  LCD CONTROLLER (LCDC)

S1C33L26 TECHNICAL MANUAL

 

Seiko Epson Corporation 

26-39

 

The following condition must be satisfied when setting VTCNT[9:0]:
 

VT > VDP + VDPS

D[15:10]  Reserved

D[9:0] 

VDPCNT[9:0]: Vertical Display Period (VDP) Setup Bits

 

Sets the vertical display period (VDP, panel vertical resolution) in line units. (Default: 0x0)

 

VDP = VDPCNT[9:0] + 1 [lines]

 

The following condition must be satisfied when setting VDPCNT[9:0]:
 

VT 

≥

 VDP + 1

 

Example: when 320 

×

 240 LCD (STN/TFT)  panel is used

 

VDP = 240

 

VDPCNT[9:0] = 240 - 1 = 239 (= 0xef) 

MOD Rate Register (LCDC_MODR)

Register name Address

Bit

Name

Function

Setting

Init. R/W

Remarks

MOD Rate 
Register
(LCDC_MODR)

0x302018

(32 bits)

D31–6 –

reserved

–

–

–

0 when being read.

D5–0 MOD[5:0]

LCD MOD rate setup

0x0 to 0x3f

0x0 R/W

D[31:6]  Reserved

D[5:0] 

MOD[5:0]: LCD MOD Rate Setup Bits

 

Sets the cycle time at which to switch the MOD signal. (Default: 0x0)

 

When this register is 0x0, the MOD signal switches at the cycle time of the FPFRAME signal. If an-
other period is desired, set the FPLINE pulse-count value. 

Horizontal Display Start Position Register (LCDC_HDPS)

Register name Address

Bit

Name

Function

Setting

Init. R/W

Remarks

Horizontal 
Display Start 
Position 
Register
(LCDC_HDPS)

0x302020

(32 bits)

D31–10 –

reserved

–

–

–

0 when being read.

D9–0 HDPSCNT

[9:0]

Horizontal display period start 
position for TFT
HT > HDP + HDPS + 1 (HR-TFT)
HT > HDP + HDPS (other TFT)

HDPS = HDPSCNT [Ts]

0x0 R/W 0x0 must be set for 

STN panels.

Note:  This register is used only for setting HR-TFT panel parameters. When using an STN panel, leave 

this register unaltered as 0x0.

D[31:10]  Reserved

D[9:0] 

HDPSCNT[9:0]: Horizontal Display Period Start Position Bits

 

Sets the horizontal display period start position (HDPS) for HR-TFT panels in pixel clock units. 

 

(Default: 0x0)

 

HDPS = HDPSCNT[9:0] + 1 [Ts]

 

 

(Ts: pixel clock period)

 

The following condition must be satisfied when setting HDPSCNT[9:0]:
 

HT > HDP + HDPS

Vertical Display Start Position Register (LCDC_VDPS)

Register name Address

Bit

Name

Function

Setting

Init. R/W

Remarks

Vertical Display 
Start Position 
Register
(LCDC_VDPS)

0x302024

(32 bits)

D31–10 –

reserved

–

–

–

0 when being read.

D9–0 VDPSCNT

[9:0]

Vertical display period start posi-
tion for TFT
VT > VDP + VDPS

VDPS = VDPSCNT [lines]

0x0 R/W 0x0 must be set for 

STN panels.

Note:  This register is used only for setting HR-TFT panel parameters. When using an STN panel, leave 

this register unaltered as 0x0.

D[31:10]  Reserved

Summary of Contents for S1C33L26



















































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for S1C33L26

Eaton AMPGARD RVSS Instruction For Installation And Maintenance preview
AMPGARD RVSS
Brand: Eaton Pages: 16
GE PACSystems* RX3i Application Manual preview
PACSystems* RX3i
Brand: GE Pages: 39
GE PACSystems* RX3i Secure Deployment Manual preview
PACSystems* RX3i
Brand: GE Pages: 35
GE PACSystems* RX3i Important Product Information preview
PACSystems* RX3i
Brand: GE Pages: 3
GE PACSystems* RX3i User Manual preview
PACSystems* RX3i
Brand: GE Pages: 169
Hable One Starting Manual preview
One
Brand: Hable Pages: 3
Federal Signal Corporation FC Description, Specifications, Installation, Operation, And Service Manual preview
FC
Brand: Federal Signal Corporation Pages: 34
Parker ER Series Maintenance Instructions & Parts List preview
ER Series
Brand: Parker Pages: 44
National Instruments sbRIO-9629 Quick Reference Manual preview
sbRIO-9629
Brand: National Instruments Pages: 2
Technische Alternative UVR 63H Operation And Installation Manual preview
UVR 63H
Brand: Technische Alternative Pages: 68
Sentiotec CV 4 Installation And Operating Instructions Manual preview
CV 4
Brand: Sentiotec Pages: 45
Cardin Elettronica S486 Series Installation And Reference preview
S486 Series
Brand: Cardin Elettronica Pages: 56
Gateway AMI 493 Firmware Update And Drive Installation preview
AMI 493
Brand: Gateway Pages: 2
Oriental motor FSC-24 Operating Manual preview
FSC-24
Brand: Oriental motor Pages: 4
U-Tron 6830-122-C10 Instruction Manual preview
6830-122-C10
Brand: U-Tron Pages: 8
Instrutech VGC301 User Manual preview
VGC301
Brand: Instrutech Pages: 42
UCS SYNCHRO QUASAR AC User Manual preview
SYNCHRO QUASAR AC
Brand: UCS Pages: 10
Curtis MultiMode 1214-8 Manual preview
MultiMode 1214-8
Brand: Curtis Pages: 41

Brands by name

Popular brands

Load more brands