manualshive.com logo in svg

Epson S1C33L26, Technical Manual

The Epson S1C33L26 Technical Manual is here to assist you in understanding the functionality and features of this incredible product. Easily accessible for download, for free, from our website, it provides comprehensive instructions and insights to maximize your experience with the Epson S1C33L26.

Share
Download
background image

28  USB FUNCTION CONTROLLER (USB)

S1C33L26 TECHNICAL MANUAL

 

Seiko Epson Corporation 

28-45

This register sets operations of the endpoint EPc.

D7 

AutoForceNAK

 

Sets the ForceNAK bit of this register to 1 when the transaction of the endpoint EPc completes normally.

D6 

EnShortPkt

 

Setting this bit to 1 enables to send the data within the FIFO that is less than the quantity specified for 
the MaxPacketSize, as a short packet for the IN transaction of the endpoint EPc. When the IN transac-
tion that transmitted short packets completes, this bit is automatically set to 0 (to be cleared). When a 
packet of the max packet size is transmitted, this bit is not cleared. 

 

If this bit is set to 1 when the FIFO has no data, a zero-length packet can be transmitted for the IN token 
from the host. If the data is written into the FIFO that is in the transmission process with the packet to 
which this bit is set, that data may be included in transmission. Therefore, do not write into the FIFO 
until the packet transmission completes and this bit is cleared.

D5 

DisAF_NAK_Short

 

When this bit is set to 0 (default setting) and the packet that was received at normal completion time of 
the OUT transaction is a short packet, the ForceNAK bit is automatically set to 1. When this bit is set to 
1, this function is disabled. 

 

When the AutoForceNAK bit is set to 1, the AutoForceNAK bit has a priority.

D4 

ToggleStat

 

Shows the status of the toggle sequence bit of the endpoint EPc.

D3 

ToggleSet

 

Sets the toggle sequence bit of the endpoint EPc to 1.

D2 

ToggleClr

 

Sets the toggle sequence bit of the endpoint EPc to 0 (to be cleared).

D1 

ForceNAK

 

If this bit is set to 1, the NAK response is done for the transaction of the endpoint EPc regardless of the 
FIFO data quantity and space capacity. 

 

When a transaction has been being done for a certain period of time, the setting of this bit will be en-
abled from the next transaction.

D0 

ForceSTALL

 

If this bit is set to 1, the STALL response is done for the transaction of the endpoint EPc. This bit has a 
priority over the setting of the ForceNAK bit. 

 

When a transaction has been being done for a certain period of time, the setting of this bit will be en-
abled from the next transaction.

EPdControl (EPd Control)

Register name Address

Bit

Name

Setting

Init. R/W

Remarks

EPdControl
(EPd control)

0x300c43

(8 bits)

D7

AutoForceNAK

1 Auto force NAK

0 Do nothing

0

R/W

D6

EnShortPkt

1 Enable short packet

0 Do nothing

0

R/W

D5

DisAF_NAK_Short

1 Disable auto force

0 Auto force NAK short

0

R/W

D4

ToggleStat

Toggle sequence bit

0

R

D3

ToggleSet

1 Set toggle sequence bit

0 Do nothing

0

W 0 when being read.

D2

ToggleClr

1 Clear toggle sequence bit 0 Do nothing

0

W

D1

ForceNAK

1 Force NAK

0 Do nothing

0

R/W

D0

ForceSTALL

1 Force STALL

0 Do nothing

0

R/W

This register sets operations of the endpoint EPd.

D7 

AutoForceNAK

 

Sets the ForceNAK bit of this register to 1 when the transaction of the endpoint EPd completes nor-
mally.

Summary of Contents for S1C33L26



















































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for S1C33L26

ABB 650 series Engineering Manual preview
650 series
Brand: ABB Pages: 128
S&C 5800 Series Troubleshooting Manual preview
5800 Series
Brand: S&C Pages: 34
ECKELMANN VS 3010 BS Operating Instruction preview
VS 3010 BS
Brand: ECKELMANN Pages: 178
H3C WX Series Registration And Activation Manual preview
WX Series
Brand: H3C Pages: 17
H3C WX Series Getting Started Manual preview
WX Series
Brand: H3C Pages: 32
IFM CR710S Original Operating Instructions preview
CR710S
Brand: IFM Pages: 49
OES ISC-9000 Operational Instructions preview
ISC-9000
Brand: OES Pages: 3
Abov MC80F0304 User Manual preview
MC80F0304
Brand: Abov Pages: 138
micro-trak MT-3405 LR F Reference Manual preview
MT-3405 LR F
Brand: micro-trak Pages: 44
SYCLOPE electronic TRACE'O Installation And Starting Instructions preview
TRACE'O
Brand: SYCLOPE electronic Pages: 40
Kärcher SensoTimer ST6 Duo eco!ogic Manual preview
SensoTimer ST6 Duo eco!ogic
Brand: Kärcher Pages: 96
Danfoss VLT MCD 201 Installation Manual preview
VLT MCD 201
Brand: Danfoss Pages: 36
DAYLIFF SUNVERTER B Installation & Operating Manual preview
SUNVERTER B
Brand: DAYLIFF Pages: 40
rotork Bifold EHPC210 Firmware Manual preview
Bifold EHPC210
Brand: rotork Pages: 22
Maintronic CBA UP Manual preview
CBA UP
Brand: Maintronic Pages: 53
Ohio Medical Push-To-Set PTS-CVR Service Manual preview
Push-To-Set PTS-CVR
Brand: Ohio Medical Pages: 25
Altronic DE-2500 Installation & Operating Instructions Manual preview
DE-2500
Brand: Altronic Pages: 70
aldes 611242-FC Installation Manual preview
611242-FC
Brand: aldes Pages: 3

Brands by name

Popular brands

Load more brands