manualshive.com logo in svg

Epson S1C33L26, Technical Manual

The Epson S1C33L26 Technical Manual is here to assist you in understanding the functionality and features of this incredible product. Easily accessible for download, for free, from our website, it provides comprehensive instructions and insights to maximize your experience with the Epson S1C33L26.

Share
Download
background image

19  UNIVERSAL SERIAL INTERFACE WITH LCD INTERFACE (USIL)

19-42

 

Seiko Epson Corporation 

S1C33L26 TECHNICAL MANUAL

Note:  This register is effective only in I

2

C slave mode. Configure USIL to I

2

C slave mode before this reg-

ister can be used.

D[7:5] 

Reserved

D4 

ISTG: I

2

C Slave Operation Trigger Bit

 

Starts an I

2

C slave operation.

 

1 (W): 

Trigger

 

0 (W): 

Ignored

 

1 (R): 

Waiting for starting operation 

 

0 (R): 

Trigger has finished (default)

 

Select an I

2

C slave operation using ISTGMOD[2:0] and write 1 to ISTG as the trigger. The I

2

C control-

ler controls the I

2

C bus to generate the specified operating status. 

D3 

Reserved

D[2:0] 

ISTGMOD[2:0]: I

2

C Slave Trigger Mode Select Bits

 

Selects an I

2

C slave operation.

8.5  Trigger List in I

Table 19.

2

C Slave Mode 

ISTGMOD[2:0]

Trigger

0x7

Reserved

0x6

ACK/NAK reception

0x5

NAK transmission

0x4

ACK transmission

0x3

Data reception/stop condition detection

0x2

Data transmission

0x1

Reserved

0x0

Wait for start condition

(Default: 0x0)

USIL I

2

C Slave Mode Interrupt Enable Register (USIL_ISIE)

Register name Address

Bit

Name

Function

Setting

Init. R/W

Remarks

USIL I

2

C Slave 

Mode Interrupt 
Enable Register 
(USIL_ISIE)

0x300671

(8 bits)

D7–2 –

reserved

–

–

–

0 when being read.

D1

ISEIE

Receive error interrupt enable

1 Enable

0 Disable

0

R/W

D0

ISIE

Operation completion int. enable

1 Enable

0 Disable

0

R/W

Note:  This register is effective only in I

2

C slave mode. Configure USIL to I

2

C slave mode before this reg-

ister can be used.

D[7:2] 

Reserved

D1 

ISEIE: Receive Error Interrupt Enable Bit

 

Enables interrupt requests to the ITC when an overrun error occurs.

 

1 (R/W):  Enabled

 

0 (R/W):  Disabled (default)

 

Set this bit to 1 to process overrun errors using interrupts.

D0 

ISIE: Operation Completion Interrupt Enable Bit

 

Enables interrupt requests to the ITC when the triggered operation has completed.

 

1 (R/W):  Enabled

 

0 (R/W):  Disabled (default)

 

Set this bit to 1 to confirm whether the triggered operation has completed or not using interrupts.

Summary of Contents for S1C33L26



















































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for S1C33L26

GE 400 Series Installation Instructions preview
400 Series
Brand: GE Pages: 2
FAAC 740 D User Manual preview
740 D
Brand: FAAC Pages: 64
EasyIO FG Series User Manual preview
FG Series
Brand: EasyIO Pages: 12
RMG GSM 3ST User Manual preview
GSM 3ST
Brand: RMG Pages: 6
Baader Planetarium Steeldrive II Manual preview
Steeldrive II
Brand: Baader Planetarium Pages: 7
H3C WX Series Configuration Manual preview
WX Series
Brand: H3C Pages: 69
H3C WX1800H series Command Reference Manual preview
WX1800H series
Brand: H3C Pages: 27
H3C WX3500H series Installations preview
WX3500H series
Brand: H3C Pages: 4
H3C WX5540H Installation Manual preview
WX5540H
Brand: H3C Pages: 54
H3C LSWM1WCM10 Manual preview
LSWM1WCM10
Brand: H3C Pages: 10
H3C LSQM1WCMB0 Quick Start Manual preview
LSQM1WCMB0
Brand: H3C Pages: 10
NCR MSR Instructions Manual preview
MSR
Brand: NCR Pages: 8
Valcom V-1092 User Manual preview
V-1092
Brand: Valcom Pages: 3
Valcom V-1092 Technical Specifications preview
V-1092
Brand: Valcom Pages: 2
Eaton SCD24 Installation Manual preview
SCD24
Brand: Eaton Pages: 8
ABB RHDE250 Operating Instruction preview
RHDE250
Brand: ABB Pages: 44
Omega CNI16D Quick Start preview
CNI16D
Brand: Omega Pages: 2
Zmotion ZMC408SCAN Hardware Manual preview
ZMC408SCAN
Brand: Zmotion Pages: 34

Brands by name

Popular brands

Load more brands