Epson S1C33L26 Technical Manual Download Page 610 | Manualshive

Page: 610 / 722

background image

29 MISC REGISTERS (MISC)

S1C33L26 TECHNICAL MANUAL

Seiko Epson Corporation

29-5

Boot Register (MISC_BOOT)

Register name Address

Bit

Name

Function

Setting

Init. R/W

Remarks

BOOT Register
(MISC_BOOT)

0x300016

(8 bits)

D7–4 BOOT[3:0] Boot mode indicator

BOOT[3:0]

Boot mode

*

R

*

Depends on the

BOOT pin status at
initial reset

0b1000
0b0100

Other

SPI/RS232C

NOR/ROM

reserved

D3–2 –

reserved

–

–

–

0 when being read.

D1

BOOT_ENA #CE10 area boot enable

1 Internal

0 External

1

R/W Write-protected

D0

–

reserved

–

–

–

0 when being read.

D[7:4]

BOOT[3:0]: Boot Mode Indicator Bits

Indicates the boot device that has been specified by the BOOT pin.

6.6 BOOT[3:0] Bits

Table 29.

BOOT[3:0]

Boot mode

0b1000

SPI/RS232C boot

0b0100

NOR Flash/external ROM boot

Other

Reserved

BOOT[3:0] is set by the system boot sequencer. Do not alter these bit values from the user routine.

D[3:2]

Reserved

D1

BOOT_ENA: #CE10 Area Boot Enable Bit

Enables fetching the RESET vector from the #CE10 external area (0xc00000).

1 (R/W): Internal boot (default)

0 (R/W): External boot

BOOT_ENA is set by the system boot sequencer. When programming a Flash memory using ICD33,
BOOT_ENA must be set to 0.

D0

Reserved

RAM Location Select Register (MISC_RAM_LOC)

Register name Address

Bit

Name

Function

Setting

Init. R/W

Remarks

RAM Location
Select Register
(MISC_RAM_
LOC)

0x300018

(8 bits)

D7–5 –

reserved

–

–

–

0 when being read.

D4

DSTRAM_
CFG

DSTRAM configuration

1 LUTRAM

0 DSTRAM

0

R/W Write-protected

D3–1 –

reserved

–

–

–

0 when being read.

D0

IVRAM_LOC IVRAM location select

1 Area 3

0 Area 0

1

R/W Write-protected

D[7:5]

Reserved

D4

DSTRAM_CFG: DSTRAM Configuration Bit

Selects whether DSTRAM in Area 3 is used as DSTRAM or LUTRAM.

1 (R/W): LUTRAM

0 (R/W): DSTRAM (default)

By default (DSTRAM_CFG = 0), DSTRAM is located in Area 3 and is used as a general-purpose RAM
or DMA control table memory.

Setting DSTRAM_CFG to 1 configures DSTRAM to LUTRAM to be used as the color look-up tables
for the LCDC. When using the color look-up tables, set DSTRAM_CFG to 1 and LUTPASS/LCDC_
DISPMOD register to 0. For more information on the color look-up tables, see the “LCD Controller
(LCDC)” chapter.

Note: When DSTRAM is switched to LUTRAM, locate the DMAC control table in IVRAM (Area 3) or

an external RAM.

D[3:1]

Reserved

D0

IVRAM_LOC: IVRAM Location Select Bit

Selects the 20KB IVRAM location.

1 (R/W): Area 3 (default)

0 (R/W): Area 0

«
...
608
609
610
611
612
...
»

Summary of Contents for S1C33L26



















































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for S1C33L26

Brand: KELCO Pages: 36

Brand: Campbell Pages: 8

iBox Hub 25020180

Brand: Hans Grohe Pages: 36

Brand: Lattice Pages: 23

Brand: Vacon Pages: 132

Brand: Wesa Pages: 8

Brand: Sartorius Pages: 165

Brand: Jetter Pages: 62

StarSign Bio Token 3.0 M

Brand: Giesecke & Devrient Pages: 28

Brand: Glitch'd Gaming Pages: 12

Brand: SIATA Pages: 7

Brand: Rain Bird Pages: 104

Brand: Sander Pages: 8

Brand: SGM Pages: 24

Brand: Bornay Pages: 66

Brand: Niko Pages: 40

1200-RD00-00-0 Series

Brand: gefran Pages: 6

Brand: BZ PRODUCTS Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands