manualshive.com logo in svg

Epson S1C33L26, Technical Manual

The Epson S1C33L26 Technical Manual is here to assist you in understanding the functionality and features of this incredible product. Easily accessible for download, for free, from our website, it provides comprehensive instructions and insights to maximize your experience with the Epson S1C33L26.

Share
Download
background image

14  8-BIT TIMERS (T8)

14-8

 

Seiko Epson Corporation 

S1C33L26 TECHNICAL MANUAL

T8 Ch.

x

 Counter Data Registers (T8_TC

x

)

Register name Address

Bit

Name

Function

Setting

Init. R/W

Remarks

T8 Ch.

x

 

Counter Data 
Register
(T8_TC

x

)

0x301104

|

0x301174

(16 bits)

D15-8 –

reserved

–

–

–

0 when being read.

D7–0 TC[7:0]

T8 counter data
TC7 = MSB
TC0 = LSB

0x0 to 0xff

0xff

R

D[15:8]  Reserved

D[7:0] 

TC[7:0]: T8 Counter Data Bits

 

The counter data can be read out. (Default: 0xff)

 

This register is read-only and cannot be written to.

T8 Ch.

x

 Control Registers (T8_CTL

x

)

Register name Address

Bit

Name

Function

Setting

Init. R/W

Remarks

T8 Ch.

x

 

Control Register
(T8_CTL

x

)

0x301106

|

0x301176

(16 bits)

D15–12 –

reserved

–

–

–

0 when being read.

D11–8 TFMD[3:0] Fine mode setup

(Ch.0 to Ch.3)

0x0 to 0xf

0x0 R/W Set a number of 

times to insert delay 
into a 16-underflow 
period.

–

reserved (Ch.4 to Ch.7)

–

–

–

0 when being read.

D7–5 –

reserved

–

–

–

D4

TRMD

Count mode select

1 One shot

0 Repeat

0

R/W

D3–2 –

reserved

–

–

–

0 when being read.

D1

PRESER

Timer reset

1 Reset

0 Ignored

0

W

D0

PRUN

Timer run/stop control

1 Run

0 Stop

0

R/W

D[15:12]  Reserved

D[11:8]  TFMD[3:0]: Fine Mode Setup Bits (Ch.0 to Ch.3)

 

Corrects the transfer rate error. (Default: 0x0)

 

TFMD[3:0] specifies the delay pattern to be inserted into a 16 underflow period. Inserting one delay 
extends the output clock cycle by one count clock cycle. This setting delays the interrupt timing in the 
same way.

10.3  Delay Patterns Specified by TFMD[3:0]

Table 14.

TFMD[3:0]

Underflow number

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

0x0

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

0x1

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

D

0x2

–

–

–

–

–

–

–

D

–

–

–

–

–

–

–

D

0x3

–

–

–

–

–

–

–

D

–

–

–

D

–

–

–

D

0x4

–

–

–

D

–

–

–

D

–

–

–

D

–

–

–

D

0x5

–

–

–

D

–

–

–

D

–

–

–

D

–

D

–

D

0x6

–

–

–

D

–

D

–

D

–

–

–

D

–

D

–

D

0x7

–

–

–

D

–

D

–

D

–

D

–

D

–

D

–

D

0x8

–

D

–

D

–

D

–

D

–

D

–

D

–

D

–

D

0x9

–

D

–

D

–

D

–

D

–

D

–

D

–

D

D

D

0xa

–

D

–

D

–

D

D

D

–

D

–

D

–

D

D

D

0xb

–

D

–

D

–

D

D

D

–

D

D

D

–

D

D

D

0xc

–

D

D

D

–

D

D

D

–

D

D

D

–

D

D

D

0xd

–

D

D

D

–

D

D

D

–

D

D

D

D

D

D

D

0xe

–

D

D

D

D

D

D

D

–

D

D

D

D

D

D

D

0xf

–

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D: Indicates the insertion of a delay cycle.

Count clock

Underflow signal (not corrected)

Underflow signal (corrected)

Output clock (not corrected)

Output clock (corrected)

Delayed

15

16

15

16

1

1

10.1  Delay Cycle Insertion in Fine Mode

Figure 14.

Summary of Contents for S1C33L26



















































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for S1C33L26

Technische Alternative UVR 63H Operation And Installation Manual preview
UVR 63H
Brand: Technische Alternative Pages: 68
Industrial Controls MC-2120 Operating And Maintenance Manual preview
MC-2120
Brand: Industrial Controls Pages: 17
Securi-Prod LK190 Installation Manual preview
LK190
Brand: Securi-Prod Pages: 3
HANYOUNG NUX TPR-3SL-EP Instruction Manual preview
TPR-3SL-EP
Brand: HANYOUNG NUX Pages: 4
Unimig UNI-FLAME REG Operation Manual preview
UNI-FLAME REG
Brand: Unimig Pages: 4
IBM ServeRAID M1215 SAS User Manual preview
ServeRAID M1215 SAS
Brand: IBM Pages: 35
3M Touch Screen Controller EX112 Reference Manual preview
Touch Screen Controller EX112
Brand: 3M Pages: 40
SAES NEG POWER User Manual preview
NEG POWER
Brand: SAES Pages: 36
S2Tech 699PLUS Instruction Manual preview
699PLUS
Brand: S2Tech Pages: 4
Zaber T-CON3 User Manual preview
T-CON3
Brand: Zaber Pages: 23
NXP Semiconductors MPC57xx Application Note preview
MPC57xx
Brand: NXP Semiconductors Pages: 11
Electrosmith 3340 VCO Build Manual preview
3340 VCO
Brand: Electrosmith Pages: 32
Fox SHUTTER Wi-STR1S2-P Manual preview
SHUTTER Wi-STR1S2-P
Brand: Fox Pages: 15
Whelen Engineering Company MPC03 Installation & Operating Manual preview
MPC03
Brand: Whelen Engineering Company Pages: 10
NI PXI-8105 Installation Manual preview
PXI-8105
Brand: NI Pages: 4
HIKVISION DS-K1F600U-D6E Series User Manual preview
DS-K1F600U-D6E Series
Brand: HIKVISION Pages: 49
Automated Logic M4106nx Technical Instructions preview
M4106nx
Brand: Automated Logic Pages: 10
Controlli MVE5 Series Mounting Instructions preview
MVE5 Series
Brand: Controlli Pages: 6

Brands by name

Popular brands

Load more brands