manualshive.com logo in svg

Epson S1C33L26, Technical Manual

The Epson S1C33L26 Technical Manual is here to assist you in understanding the functionality and features of this incredible product. Easily accessible for download, for free, from our website, it provides comprehensive instructions and insights to maximize your experience with the Epson S1C33L26.

Share
Download
background image

REVISION HISTORY

Code No.

Page

Contents

411900101

19-28

USIL: Interrupts in UART mode - Receive error interrupt
(Old)  ... If any of the error flags has the value 1, ... proceed with error recovery.
(New) ... If any of the error flags has the value 1, ... proceed with error recovery.
 

To reset an overrun error, ... USILMOD[2:0]/USIL_GCFG register) to initialize USIL.

19-29

USIL: Interrupts in SPI mode - Receive error interrupt
(Old)  ... If SEIF is 1, the interrupt handler routine will proceed with error recovery.
(New) ... If SEIF is 1, the interrupt handler routine will proceed with error recovery.
 

To reset an overrun error, clear SEIF ... then read the receive data buffer (USIL_RD register) twice.

19-30

USIL: Interrupts in I

2

C master/slave mode - Receive error interrupt

(Old)  To use this interrupt, ...  interrupt requests for this cause will not be sent to the ITC. ... 
 

... If IMEIF is 1, the interrupt handler routine will proceed with error recovery.

(New) To use this interrupt, ...  interrupt requests for this cause will not be sent to the ITC.
 

An overrun error occurs ... two-byte data has been received without reading the receive data buffer.

 

The USIL module sets ...  the interrupt handler routine will proceed with error recovery.

 

To reset an overrun error, ... read the receive data buffer (USIL_RD register) twice.

19-32, 
19-38, 

AP-A-3, 

AP-A-28

USIL: 0x30065f USIL SPI Master Mode Receive Data Mask Register (USIL_SMSK)
(New) Deleted

19-33

USIL: USIL Receive Data Buffer Register (USIL_RD) - (D[7:0]) RD[7:0]: USIL Receive Data Buffer Bits
(Old)  If receiving the subsequent data is completed ... the new received data overwrites the contents.
(New) Deleted

19-36

USIL: USIL UART Mode Interrupt Flag Register (USIL_UIF) - (D2) UOEIF: Overrun Error Flag Bit
(Old)  An overrun error occurs when the previous received data ... UOEIF is reset by writing 1.
(New) An overrun error occurs ... (write 0x0 to USILMOD[2:0]/USIL_GCFG register) to initialize USIL.

19-36, 
19-37, 

AP-A-28

USIL: USIL SPI Master/Slave Mode Configuration Register (USIL_SCFG)
(Old)  D1 SMSKEN: Receive Data Mask Enable Bit
(New) D1 Reserved (Do not set to 1.)

19-38, 19-39 USIL: USIL SPI Master/Slave Mode Interrupt Flag Register (USIL_SIF) - (D2) SEIF: Overrun Error Flag Bit

(Old)  An overrun error occurs when the previous received data ... SEIF is reset by writing 1.
(New) An overrun error occurs if data are received successively when SRDIF is 1. While SRDIF is set ...
 

The procedure that writes 1 to SEIF and reads USIL_RD register twice can be reversed.

19-41

USIL: USIL I

2

C Master Mode Interrupt Flag Register (USIL_IMIF) - (D[4:2]) IMSTA[2:0]: I

2

C Master Status 

Bits
(Old)  When an operation completion interrupt occurs, ... the operation that has been finished.
(New)... the operation that has been finished. IMSTA[2:0] is automatically reset to 0x0 by writing 1 to IMIF.
USIL: USIL I

2

C Master Mode Interrupt Flag Register (USIL_IMIF) - (D1) IMEIF: Overrun Error Flag Bit

(Old)  An overrun error occurs when the previous received data ... IMEIF is reset by writing 1.
(New) An overrun error occurs ... and then read the receive data buffer (USIL_RD register) twice.

19-43

USIL: USIL I

2

C Slave Mode Interrupt Flag Register (USIL_ISIF) - (D[4:2]) ISSTA[2:0]: I

2

C Slave Status Bits

(Old)  When an operation completion interrupt occurs, ... the operation that has been finished.
(New)... the operation that has been finished. ISSTA[2:0] is automatically reset to 0x0 by writing 1 to ISIF.
USIL: USIL I

2

C Slave Mode Interrupt Flag Register (USIL_ISIF) - (D1) ISEIF: Overrun Error Flag Bit

(Old)  An overrun errors occurs when the previous received data ... ISEIF is reset by writing 1.
(New) An overrun error occurs ... and then read the receive data buffer (USIL_RD register) twice.

19-45

USIL: USIL LCD SPI Mode Interrupt Flag Register (USIL_LSIF) - (D1) LSBSY: Transfer Busy Flag Bit
(Old)  It is cleared to 0 once the transfer is completed.
(New) It is cleared to 0 after data transfer ... LSDMOD[1:0]/USIL_LSDCFG register has completed.

21-4, 21-17 I

2

S: Sample clock period

Modified Figures 21.4.2 and 21.7.8

21-10

I

2

S: Data output timing chart 

Modified Figure 21.5.2

21-18

I

2

S: I

2

S Start/Stop Register (I2S_START) - (D7) I2SBUSY: I

2

S Busy Flag Bit

(Old)  I2SBUSY is set to 1 when the I

2

S starts data output and stays 1 while data is being output.

(New) I2SBUSY is set to 1 when 1 is written to I2SSTART and stays 1 while data is being output.

24-7, 24-17 GPIO: Interrupt mode and polarity selection

(Old)  In SLEEP mode, the CMU senses the port interrupt ... if edge trigger mode is selected.
(New) SLEEP mode can be canceled ... how the GPIO interrupt mode (edge trigger/level trigger) is set.

26-2

LCDC: Block diagram
Modified Figure 26.2.1
LCDC: Block diagram
(Old)  SAPB bus interface
 

The C33 PE Core accesses the LCDC registers and look-up table through ...

 

Sequence controller

 

The sequence controller controls data flow ... through the look-up table. ...

(New) SAPB bus interface
 

The C33 PE Core accesses the LCDC registers and monochrome look-up table through ...

 

Sequence controller

 

The sequence controller controls data flow ... through the color look-up table. ...

Summary of Contents for S1C33L26



















































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for S1C33L26

Häfele 633.03.298 Operating Instructions Manual preview
633.03.298
Brand: Häfele Pages: 24
IAI ROBO Cylinder RCP2 Series Quick Start Manual preview
ROBO Cylinder RCP2 Series
Brand: IAI Pages: 5
Bailey infi 90 IMMFP12 Instruction preview
infi 90 IMMFP12
Brand: Bailey Pages: 75
VDH ALFANET 1-LS User Manual preview
ALFANET 1-LS
Brand: VDH Pages: 4
VIRDI AC-2200 User Manual preview
AC-2200
Brand: VIRDI Pages: 73
Arcus PMX-4EX-SA User Manual preview
PMX-4EX-SA
Brand: Arcus Pages: 97
Harsen GU641A Operation Manual preview
GU641A
Brand: Harsen Pages: 55
Wabtec Ricon 55914 Installation Instructions preview
Ricon 55914
Brand: Wabtec Pages: 5
YASKAWA SI-T/ V7 Technical Manual preview
SI-T/ V7
Brand: YASKAWA Pages: 157
Cypress CapSense Plus CY3280-CPM1 Quick Start Manual preview
CapSense Plus CY3280-CPM1
Brand: Cypress Pages: 4
Infineon Technologies TC1796 User Manual preview
TC1796
Brand: Infineon Technologies Pages: 2150
DAGON SPM-12 Manual Instruction preview
SPM-12
Brand: DAGON Pages: 8
D+H DXD 300-BSY+ Original Instructions Manual preview
DXD 300-BSY+
Brand: D+H Pages: 16
Yaesu G-800DXA User Manual preview
G-800DXA
Brand: Yaesu Pages: 20
Nidec Leroy-Somer R121 Installation And Maintenance Manual preview
Leroy-Somer R121
Brand: Nidec Pages: 16
3Ware 720-0127-02 Manual preview
720-0127-02
Brand: 3Ware Pages: 122
Leviton 73A00-3ZB Installation Instructions And User Manual preview
73A00-3ZB
Brand: Leviton Pages: 2
AMX NetLinx NXI Operation/Reference Manual preview
NetLinx NXI
Brand: AMX Pages: 26

Brands by name

Popular brands

Load more brands